Southbend Oven SSB 32 User Manual

IMPORTANT FOR FUTURE REFERENCE  
Please complete this information and retain  
this manual for the life of the equipment:  
Model #: __________________________  
Serial #: __________________________  
Date Purchased: ___________________  
Owner’s Manual  
Platinum Series  
Radiant Steakhouse Broiler  
Models SSB-32, SSB-36, and SSB-45  
WARNING  
Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death.  
Read installation, operation, and maintenance instructions thoroughly before installing or servicing this equipment.  
1100 Old Honeycutt Road, Fuquay-Varina, NC 27526 USA • www.southbendnc.com  
MANUAL 1190950 (02/09)  
$30.00  
RADIANT STEAKHOUSE BROILER  
MANUAL SECTION SR  
 
RADIANT STEAKHOUSE BROILER  
INTRODUCTION  
INTRODUCTION  
Congratulations! You have purchased one of the finest pieces of heavy-duty commercial cooking equipment on the  
market.  
You will find that your new equipment, like all Southbend equipment, has been designed and manufactured to meet  
the toughest standards in the industry. Each piece of Southbend equipment is carefully engineered and designs are  
verified through laboratory tests and field installations. With proper care and field maintenance, you will experience  
years of reliable, trouble-free operation. For best results, read this manual carefully.  
RETAIN THIS MANUAL FOR FUTURE REFERENCE.  
This manual is for the Southbend Radiant Steakhouse Broiler, which may be mounted on a stand, a cabinet, a  
refrigeration base, or a countertop. The serial plate is located in the rear right lower corner (see Figure 1 below).  
Southbend steakhouse broilers are unique in design. They utilize Southbend’s high performance radiant burners to  
provide broiling temperatures of up to 850°F (454°C) on the rack surface. The spent gases are then baffled and  
transferred to the top searing griddle providing a uniform temperature of 650°F (343°C). This secondary cooking  
surface is perfect for searing meat and locking in juices before broiling, and is provided without additional fuel cost or  
burners.  
The broiler design supplies 100% clean primary air to the burners, ensuring efficient combustion and maintaining full  
production capacity and maximum recovery even in the most severe conditions of grease vapors and smoke  
atmospheres, which are created during any broiling process.  
Read these instructions carefully before attempting installation. Installation and initial startup should be performed by  
a qualified installer. Unless the installation instructions for this product are followed by a qualified service technician (a  
person experienced in and knowledgeable of the installation of commercial gas and/or electric cooking equipment)  
then the terms and conditions on the Manufacturer’s Limited Warranty will be rendered void and no warranty of any  
kind shall apply.  
In the event you have questions concerning the installation, use, care, or service of the product, contact:  
Southbend Technical Service  
1100 Old Honeycutt Road  
Fuquay-Varina, North Carolina 27526 USA  
Figure 1  
Location of Serial Plate  
Location of Serial Plate  
(on rear of unit)  
OWNERS MANUAL 1190950 (02/09)  
 
PAGE 3 OF 20  
 
SPECIFICATIONS  
RADIANT STEAKHOUSE BROILER  
SPECIFICATIONS  
NOTICE  
Local codes regarding installation vary greatly from one area to another. The National Fire Protection Association,  
Inc. states in its NFPA 96 latest edition that local codes are the “authority having jurisdiction” when it comes to  
installation requirements for equipment. Therefore, installations must comply with all local codes, or in the absence  
of local codes, with the National Fuel Gas Code, ANSI Z223.1, Natural Gas Installation Code, CAN/CGA-B149.1,  
or the Propane Installation Code CAN/CGA-B149.2, as applicable, including:  
1. The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during  
any pressure testing of that system at test pressures in excess of 1/2 psi (3.45 kPa).  
2. The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff  
valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2  
psi (3.45 kPa).  
Southbend reserves the right to change specifications and product design without notice. Such revisions do not  
entitle the buyer to corresponding changes, additions, or replacements for previously purchased equipment.  
This product is intended for commercial use only, not for household use.  
CLEARANCES  
There must be adequate clearance between the broiler and adjacent construction due to the heat generated by the  
broiler. Clearance must also be provided for servicing and for operation.  
The minimum clearance from non-combustible construction is 6 inches (152 mm) on the sides and rear (to permit  
combustion air to enter the rear of the broiler). To service the broiler components, all models require at least 6 inches  
(152 mm) accessibility-clearance on the right and left side.  
Adequate clearance must be provided in front of the broiler for operation and cleaning.  
The high-temperature flue products from the broiler burners flow out through a flue chamber at the top rear of the  
broiler. Installation under a vented hood is recommended.  
WARNING  
MINIMUM CLEARANCES FROM COMBUSTIBLE CONSTRUCTION  
The stand mount, cabinet mount and countertop model require a minimum clearance from combustible surfaces of  
6 inches (152 mm) on the sides and rear.  
PAGE 4 OF 20  
OWNERS MANUAL 1190950 (02/09)  
 
 
RADIANT STEAKHOUSE BROILER  
SPECIFICATIONS  
DIMENSIONS  
Figure 2  
Dimensions in Inches (Millimeters)  
Minimum Clearances 6" (152) Rear and Sides  
A
41.5" (1054)  
38.75" (984)  
57.0"  
(1448)  
Floor to  
Griddle Surface  
52.5" (1334)  
Floor to  
Broiler Surface  
(Lowest Position)  
41.0" (1041)  
FRONT VIEW  
RIGHT SIDE VIEW  
Total BTU’s  
Number  
Burners  
Model Number  
Width “A”  
Crated Weight  
Nat Gas  
84,000  
Propane  
73,000  
SSB-32  
SSB-36  
SSB-45  
32" (813 mm)  
36" (914 mm)  
45" (1143 mm)  
2
2
3
428 lbs (195 kg)  
512 lbs (232 kg)  
616 lbs (279 kg)  
84,000  
73,000  
126,000  
109,500  
VENTILATION  
WARNING  
Improper ventilation can result in personal injury or death. Ventilation, which fails to properly remove flue products,  
can cause headaches, drowsiness, nausea, or could result in death.  
The flue vent, located at the top rear of the unit, must not be blocked or covered at any time.  
All gas appliances must be installed in such a manner that the flow of combustion and ventilation air is not  
obstructed. Provisions for adequate air supply must be provided.  
NOTICE  
Proper ventilation is the owner’s responsibility. Any problem due to improper ventilation will not be covered by the  
warranty.  
Do not obstruct the rear of the broiler since combustion air enters through this area. Be sure to inspect and clean  
the ventilation system according to the ventilation equipment manufacturer’s instructions.  
OWNERS MANUAL 1190950 (02/09)  
 
PAGE 5 OF 20  
 
SPECIFICATIONS  
RADIANT STEAKHOUSE BROILER  
If a ventilation canopy is used, it is recommended that the canopy extend 6" (152 mm) past the broiler and that the  
bottom edge be located 6'6" (1980 mm) from the floor. Filters should be installed at an angle of 45° or more from the  
horizontal. This position prevents dripping grease, and facilitates collecting the run-off grease in a drip pan under the  
filter.  
A strong exhaust fan tends to create a vacuum in the room and may interfere with burner performance or may  
extinguish pilot flames. Fresh air openings approximately equal to the fan area will relieve such a vacuum. The  
exhaust fan should be installed at least 2" (51 mm) above the vent opening on the top rear of the broiler.  
If the broiler is connected directly to an outside flue, a CSA design-certified down draft diverter must be installed.  
In case of unsatisfactory performance by any gas appliance, check the appliance with the exhaust fan turned OFF. Do  
this only long enough to check whether doing so corrects any problems with equipment performance. Then turn the  
exhaust fan back on and let it run to remove any exhaust that may have accumulated during the test.  
GAS SUPPLY  
The broiler is design-certified for operation on natural or propane gases. The broiler is shipped configured and  
adjusted for the type of gas specified by the purchaser, which is indicated on the serial plate (see Figure 1 on page 3).  
Connect the broiler ONLY to the type of gas for which it is configured and adjusted.  
Gas Type  
Total BTU/hour  
Burner Orifice  
Bar Pilot.  
Min. Supply Pressure  
Manifold Pressure  
42,000 Per  
Burner  
Natural Gas  
No. 36 (P/N 1006436)  
No. 75 (P/N 1176664)  
7" W.C.  
6" W.C.  
36,500 Per  
Burner  
Propane  
No. 51 (P/N 1006451)  
No. 79 (P/N 1176665)  
11" W.C.  
10" W.C.  
Models with a rear gas connection have a 1" rear gas connection to an external regulator that is located at the rear  
bottom corner on the right side. Models with a front gas supply are connected by unions assembled to the front  
manifold.  
Minimum supply pressure is 7" W.C. for natural gas, 11" W.C. for propane. An external pressure regulator and shutoff  
valve are provided. If using a flexible-hose gas connection, the inside diameter of the hose must not be smaller than  
the connector on the broiler, and must comply with ANSI Z21.69. Provide an adequate means of restraint to prevent  
undue strain on the gas connection. Test pressure should not exceed 14" W.C.  
If applicable, the vent line from the gas appliance pressure regulator must be installed to the outdoors in accordance  
with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1, Natural Gas  
Installation Code, CAN/CGA-B149.1, or the Propane Installation Code CAN/CGA-B149.2, as applicable.  
An adequate gas supply is imperative. Undersized or low-pressure lines will restrict the volume of gas required for  
satisfactory performance. Fluctuations of more than 25% on natural gas or 10% on propane gas will create problems  
and affect burner-operating characteristics. A 1/8" pressure tap is located on the manifold to measure the manifold  
pressure. The supply line to the broiler should be no smaller than the inside diameter of the pipe on the broiler to  
which it is connected.  
PAGE 6 OF 20  
OWNERS MANUAL 1190950 (02/09)  
 
RADIANT STEAKHOUSE BROILER  
OPERATION  
OPERATION  
DANGER  
EXPLOSION HAZARD  
In the event a gas odor is detected, shut down equipment at the main shutoff valve. Immediately call the  
emergency phone number of your gas supplier.  
CAUTION  
If the broiler pilots should go out, the flow of gas to the broiler burners is NOT interrupted. Consequently, it is the  
responsibility of the operator to check the ignition of the burners immediately EVERY TIME the broiler is turned on.  
Should ignition fail after 10 seconds, turn off burners, wait 5 minutes, and then try again.  
OPERATION OF RADIANT STEAKHOUSE BROILER  
The location of the broiler controls and other components are shown in Figure 3 on the next page.  
Southbend radiant steakhouse broilers offer the intensity to broil the thickest cuts of meat at reduced cook times, the  
adjustability to finish delicate dishes to perfection, and the versatility of a griddle surface to sear and prepare non-  
broiled menu items.  
Southbend radiant steakhouse broilers require a preheat time of 5 minutes to stabilize rack temperatures and 30  
minutes for the griddle to reach even heat distribution temperatures for searing. The burner flame may lift until  
temperatures stabilize and reach operating temperature. When the ceramic tiles appear to glow evenly red, the  
broiler is ready to accept product. The broiling rack adjusts to nine heights, and rolls out for easy access.  
The cooking area has removable racks and drip trays for cleaning. As food cooks, drippings drain into a grease  
drawer located on the front of the unit next to the burner control knobs. To operate the broiler, do the following:  
1. Light the constant-burning pilots located near the front of the broiler burners (unless they are already lit).  
2. If necessary, pull out and empty the bottom grease drawer and the griddle grease chute. Keep the drip pans in  
place below the rack when broiling! Without them in place, excessive air will be pulled past the burners, reducing  
temperature and cooking efficiency.  
3. Turn the burner controls to HIGH and visually check that the burners have ignited. When the burners ignite, a blue  
flame will carry across the ceramic tiles. Flames may lift from the burner until temperatures stabilize. When the  
burner control is set to HIGH, the ceramic tips will glow red across the entire tile. When the burner control is set  
to LOW, the ceramics tips will glow red across 2/3 of each tile. (If the flame continues to lift after 10 minutes, or if  
the flame remains yellow and sooting occurs, the broiler requires adjustment by a service technician.)  
4. If searing the food to mark it with grid marks is desired, before placing food on the broiler rack move the rack to its  
highest position and allow the burners to operate on HIGH for five minutes to heat the rack surface.  
5. Turn the burner control to HIGH or LOW (as appropriate for the food to be cooked).  
6. Raise or lower the broiler rack to the height appropriate for the food to be cooked. A clicking noise will indicate  
changes in rack position when lowering the rack. To lower the rack, simply push down on the ball knob. To raise  
the rack, depress the paddle handle.  
7. Pull out the rack, place food on the rack, and slide the rack back into the broiler. (It is recommended the rack be in  
the lowest position when loading food.)  
8. Broil food for the appropriate time, turning it when appropriate. Periodically check the broiler grease drawer and  
grease chute and empty them when necessary.  
9. When done broiling, turn the burner controls to OFF. (To keep the broiler rack hot in order to mark food with sear  
marks without preheating, turn the burner controls to LOW and move the broiler rack to its highest position.)  
OWNERS MANUAL 1190950 (02/09)  
 
PAGE 7 OF 20  
OPERATION  
RADIANT STEAKHOUSE BROILER  
Figure 3  
Broiler Controls and Components  
Flue Vent Chamber  
Removable  
Grease Chute  
Pilot Adjustment  
Access Hole  
Removable  
Heavy-Duty  
Broil Rack  
Removable  
Stainless Steel  
Drip Pan  
Gas Regulator with  
1" Rear Connection  
Variable High-Low-Off  
Independent Gas  
Adjustment  
Release Paddle  
Nine-Position Rack  
Adjustment Arm  
Removable  
Grease Drawer  
Keep the drip pans in place below the rack when broiling! Without them in place,  
excessive air will be pulled past the burners, reducing temperature and cooking efficiency.  
LIGHTING AFTER GAS HAS BEEN SHUT OFF  
When turning on the main gas supply to an appliance or a group of appliances, do the following:  
1. Make sure that all the control valves and power switches of all the appliances are in the OFF position.  
2. Turn on the main gas supply valve.  
3. Light the standing pilots of each connected appliance.  
LIGHTING BROILER PILOTS  
The pilots should burn continuously unless the broiler is to be completely shut down. The broiler cavity has two or  
three pilots, one near each burner. If the pilots are extinguished, the pilot gas supply is NOT automatically interrupted.  
To light the pilots, do the following:  
1. Turn the control valves on the front of the broiler to OFF.  
2. Turn on the gas supply to the broiler (if not already on).  
3. Light the pilots.  
SHUTDOWN OF BROILER  
To place the broiler in a standby state (ready for use), turn the burner control valves to OFF. The pilots will remain lit.  
To completely shut down the broiler for an extended period (or prior to disconnecting the gas supply), turn OFF the  
manual shutoff valves of all gas supply connections. (This will extinguish all pilots.)  
PAGE 8 OF 20  
OWNERS MANUAL 1190950 (02/09)  
 
 
RADIANT STEAKHOUSE BROILER  
CLEANING & MAINTENANCE  
CLEANING & MAINTENANCE  
WARNING  
Shut off the gas supply to the appliance before cleaning or performing maintenance on any gas appliance.  
The appliance may be equipped with a restraint device to limit its movement in order to prevent damage to the  
gas connection. If disconnection of this restraint is necessary to move the appliance for cleaning or  
maintenance, reconnect the restraint when the appliance is moved back to its original installed position.  
Southbend equipment is sturdily constructed of the best materials and is designed to provide durable service when  
treated with ordinary care. To provide the best performance, your equipment must be maintained in good condition  
and cleaned daily. Naturally, the periods for this care and cleaning depend on the amount and degree of usage.  
Following daily and periodic maintenance procedures will enhance long life for your equipment. Climatic conditions  
(such as salt air) may require more thorough and frequent cleaning or the life of the equipment could be adversely  
affected.  
Keep exposed, cleanable areas of the broiler clean at all times. (See next page for instructions on cleaning stainless  
steel and baked-enamel surfaces.)  
DAILY CLEANING AND MAINTENANCE  
To prevent excess smoking, the broiler grids, bottom grease drawer, griddle grease chute, and the other broiler  
components must be kept clean of food remnants. Use a wire brush or similar scraping utensil. DO NOT use steel  
wool or a similar scrub pad that will leave small particles, which can get into food. The daily cleaning procedure is as  
follows:  
1. Use a Norton Alundum Griddle Brick to clean the griddle. Never wash a griddle with soap and water.  
2. Remove the griddle grease chute and clean it.  
3. Move the broiling rack to the low position. Pull out the rolling broiler rack.  
4. Lift out the broiler grids and clean them with a wire brush or non-toxic solvent.  
5. Lift out the drip shields and clean them with soap and water.  
6. With the rolling rack pulled-out to its stop, clean all parts where residue can collect.  
7. Clean all parts of the raising and lowering frame.  
8. Lubricate bearings with cooking oil (this helps to extend the life of the bearings).  
9. Reassemble broiling rack drip shields and grids.  
10. Remove the bottom grease drawer and clean it.  
11. Wipe clean all exterior surfaces.  
12. Check that nothing has been placed on top of the broiler flue (which will block the escape of combustion exhaust).  
13. Check that the air-intake openings on the rear of the broiler are not obstructed.  
MONTHLY CLEANING AND MAINTENANCE  
The following tasks should be performed monthly:  
1. Check for proper pilot operation. The flame on each pilot should be just large enough to extend along the flame  
carrier to the burner surface. If adjustment is necessary, call for service.  
2. Check for proper burner operation. When the burner control is set to HIGH, a blue flame will carry across the  
ceramics tiles. The ceramics tile tips will glow red across entire tile. When the burner control is set to LOW, the  
ceramics tips will glow red across 2/3 of each tile. If the flame is yellow or sooting occurs, request adjustment by a  
service technician.  
SEMIANNUAL CLEANING AND MAINTENANCE  
At least twice a year the venting system should be examined and cleaned.  
OWNERS MANUAL 1190950 (02/09)  
 
PAGE 9 OF 20  
CLEANING & MAINTENANCE  
RADIANT STEAKHOUSE BROILER  
CARE OF GRIDDLES  
The griddle should be carefully cared for in order to avoid possible damage. Use a Norton Alundum Griddle Brick to  
clean the griddle. Do not use any type of steel wool because small particles may be left on the surface and get into  
food products. Never allow water on a hot griddle, and never wash it with soap and water. Do not strike the griddle  
with utensils as this will cut and pit the griddle plate, leaving it rough and hard to clean.  
STAINLESS-STEEL SURFACES  
To remove normal dirt, grease and product residue from stainless steel surfaces that operate at LOW temperature,  
use ordinary soap and water (with or without detergent) applied with a sponge or cloth. Dry thoroughly with a clean  
cloth.  
To remove BAKED-ON grease and food splatter, or condensed vapors; apply cleanser to a damp cloth or sponge and  
rub cleanser on the metal in the direction of the polishing lines on the metal. Rubbing cleanser, as gently as possible,  
in the direction of the polished lines will not mar the finish of the stainless steel. NEVER RUB WITH A CIRCULAR  
MOTION. Soil and burnt deposits, which do not respond to the above procedure, can usually be removed by rubbing  
the surface with SCOTCH-BRITE scouring pads or STAINLESS scouring pads. DO NOT USE ORDINARY STEEL  
WOOL as any particles left on the surface will rust and further spoil the appearance of the finish. NEVER USE A  
WIRE BRUSH, STEEL SCOURING PADS (EXCEPT STAINLESS), SCRAPER, FILE OR OTHER STEEL TOOLS.  
Surfaces, which are marred, collect dirt more rapidly and become more difficult to clean. Marring also increases the  
possibility of corrosive attack. Refinishing may then be required.  
“Heat tint” is darkened areas that sometimes appear on stainless steel surfaces where the area has been subjected to  
excessive heat. These darkened areas are caused by thickening of the protective surface of the stainless steel and  
are not harmful. Heat tint can normally be removed by the foregoing, but tint which does not respond to this procedure  
calls for a vigorous scouring in the direction of the polish lines using SCOTCH-BRITE scouring pads or a STAINLESS  
scouring pad in combination with a powered cleanser. Heat tint may be lessened by reducing heat to the equipment  
during slack periods.  
PAGE 10 OF 20  
OWNERS MANUAL 1190950 (02/09)  
 
RADIANT STEAKHOUSE BROILER  
INSTALLATION  
INSTALLATION  
NOTICE  
These installation procedures must be followed by qualified personnel or warranty will be void.  
Local codes regarding installation vary greatly from one area to another. The National Fire Protection Association,  
Inc. states in its NFPA 96 latest edition that local codes are the “authority having jurisdiction” when it comes to  
installation requirements for equipment. Therefore, installations must comply with all local codes, or in the absence  
of local codes, with the National Fuel Gas Code, ANSI Z223.1, Natural Gas Installation Code, CAN/CGA-B149.1,  
or the Propane Installation Code CAN/CGA-B149.2, as applicable, including:  
1. The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during  
any pressure testing of that system at test pressures in excess of 1/2 psi (3.45 kPa).  
2. The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve  
during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.45  
kPa).  
STEP 1: UNPACKING  
IMMEDIATELY INSPECT FOR SHIPPING DAMAGE  
All containers should be examined for damage before and during unloading. The freight carrier has assumed  
responsibility for its safe transit and delivery. If damaged equipment is received, either apparent or concealed, a  
claim must be made with the delivering carrier.  
Apparent damage or loss must be noted on the freight bill at the time of delivery. The freight bill must then be  
signed by the carrier representative (Driver). If the bill is not signed, the carrier may refuse the claim. The carrier  
can supply the necessary forms.  
A request for inspection must be made to the carrier within 15 days if there is concealed damage or loss that is not  
apparent until after the equipment is uncrated. The carrier should arrange an inspection. Be certain to hold all  
contents plus all packing material.  
1. Cut the banding straps and remove the corrugated cardboard surrounding the broiler. Do not remove any of the  
attached tags or labels until the broiler is installed and working properly.  
2. Cut the banding strap holding the broiler to the wooden skid.  
3. If installing the broiler on a stand, go to Step 2a.  
If installing the broiler on a countertop, go to Step 2b.  
OWNERS MANUAL 1190950 (02/09)  
 
PAGE 11 OF 20  
INSTALLATION  
RADIANT STEAKHOUSE BROILER  
STEP 2A: MOUNT ON HEAVY DUTY STAND  
The stand is crated separately, but is shipped with the broiler. Depending on the shipping requirements, the broiler  
may already be assembled to the stand.  
1. The broiler will be attached to the stand using four ¼"-20 bolts and lock washers provided with the stand.  
Remove the bolts and lock washers from the stand.  
2. Lift the broiler (using two people is recommended). (Depending on the size and weight of the unit, it may be  
helpful to remove the griddle plate before lifting the broiler. To do so, remove the body sides to access griddle  
plate mounting bolts.) Place the broiler on the stand so the holes in the mounting flange align with the  
corresponding holes in the stand. The valve panel flange should sit flush with front frame of the stand. Secure the  
broiler to the stand with the ¼"-20 bolts and lock washers.  
3. Go on to Step 3.  
Figure 4  
Mounting Broiler on Stand  
If assembled broiler is too heavy to lift, remove side panels  
and then remove griddle top by removing four bolts.  
Fasten broiler to stand with four 1/4-inch bolts here.  
PAGE 12 OF 20  
OWNERS MANUAL 1190950 (02/09)  
 
RADIANT STEAKHOUSE BROILER  
INSTALLATION  
STEP 2B: ATTACH COUNTERTOP LEGS  
The broiler may set on a countertop using short legs. Be sure that the countertop is rated to support the crated weight  
of the broiler (see Figure 2 on page 5). The model number is shown on the serial plate located in the rear right corner  
of you broiler (see Figure 1 on page 3).  
1. With the broiler lying on its back side, screw the four legs tightly into the leg pads, as shown below. Lift the broiler  
(using two people is recommended) and set it in place on the countertop. Adjust the legs as needed to level unit.  
2. Position the broiler to the specified minimum clearances (see page 4).  
3. Go on to Step 3.  
Figure 5  
Installation on Countertop  
Screw legs into leg pads here.  
OWNERS MANUAL 1190950 (02/09)  
 
PAGE 13 OF 20  
INSTALLATION  
RADIANT STEAKHOUSE BROILER  
STEP 3: CONNECT GAS SUPPLY  
If the broiler is being installed at over 2,000 feet (610 meters) altitude and that information was not specified when  
ordered, contact the appropriate authorized Southbend Service Representative or the Southbend Service  
Department. Failure to install with proper orifice sizing will result in poor performance and may void the warranty.  
The broiler is design-certified for operation on natural or propane gases. The broiler is shipped configured and  
adjusted for the type of gas specified by the purchaser, which is indicated on the serial plate (see Figure 1 on page 3).  
Connect the broiler ONLY to the type of gas for which it is configured and adjusted.  
The broiler will have a 1" NPT female thread in the regulator at the rear of the unit, or may be connected by the front  
manifold when connected to a battery of other sectional equipment.  
Minimum supply pressure is 7" W.C. for natural gas, 11" W.C. for propane. An external pressure regulator is provided.  
If using a flexible-hose gas connection, the inside diameter of the hose must not be smaller than the connector on the  
broiler, and must comply with ANSI Z21.69. Provide an adequate means of restraint to prevent undue strain on the  
gas connection.  
If applicable, a vent line from the gas appliance pressure regulator must be installed to the outdoors in accordance  
with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1, Natural Gas  
Installation Code, CAN/CGA-B149.1, or the Propane Installation Code CAN/CGA-B149.2, as applicable.  
An adequate gas supply is imperative. Undersized or low-pressure lines will restrict the volume of gas required for  
satisfactory performance. Fluctuations of more than 25% on natural gas or 10% on propane gas will create problems  
and affect burner-operating characteristics. A 1/8" pressure tap is located on the manifold to measure the manifold  
pressure. The supply line to the broiler should be no smaller than the inside diameter of the pipe on the broiler to  
which it is connected.  
CAUTION  
ALL PIPE JOINTS AND CONNECTIONS MUST BE TESTED THOROUGHLY FOR GAS LEAKS. USE ONLY  
SOAPY WATER FOR TESTING ON ALL GASES. NEVER USE AN OPEN FLAME TO CHECK FOR GAS LEAKS.  
ALL CONNECTIONS MUST BE CHECKED FOR LEAKS AFTER THE APPLIANCE HAS BEEN PUT INTO  
OPERATION. TEST PRESSURE SHOULD NOT EXCEED 14" W.C.  
1. Check that the control valves on the broiler are in the OFF position.  
2. Purge the gas supply line to clean out dust, dirt, or other foreign matter before connecting the line to the broiler.  
3. For stand mount and countertop mounting, connect the gas supply to the inlet at right rear corner.  
CAUTION  
HOLD THE INLET SUPPLY PIPE WITH A WRENCH WHEN TIGHTENING ADDED FITTINGS TO AVOID  
DAMAGE TO THE REGULATOR, VALVE, AND OTHER COMPONENTS.  
4. Turn on the gas and check for leaks using soapy water.  
STEP 4: CHECK THE INSTALLATION  
1. Check that all screws and bolts are tightened.  
2. Check that the gas connection has been made correctly.  
3. Move the broiler into the final position at which it will be operated.  
4. Check that the broiler is level.  
5. Check that the appropriate minimum clearances are satisfied (see page 4), including adequate clearance for  
combustion air to enter the rear of the broiler.  
6. Check that there is sufficient clearance to pull out the broiler rack, grease drawer, and griddle grease chute; and  
to operate the rack-height adjustment lever.  
7. Check that adequate ventilation (fresh air supply and hood exhaust) is available to the room in which the  
appliance will operate.  
8. Wipe clean all surfaces.  
PAGE 14 OF 20  
OWNERS MANUAL 1190950 (02/09)  
 
RADIANT STEAKHOUSE BROILER  
INSTALLATION  
STEP 5: CHECK BROILER OPERATION  
1. Turn the gas supply on. Immediately check all gas connections for leaks using soapy water.  
2. Light the pilots and check that the pilot flames are large enough to extend along the flame carrier to the burner  
surface. If not, adjust the pilots (see page 17).  
3. Turn the burner control to HIGH and visually check that the burners have ignited. When the burners ignite, a blue  
flame will carry across the ceramics tiles. Flames may lift from the burners until temperatures stabilize. When the  
burner control is set to HIGH, the ceramics tips will glow red across the entire tile. When the burner control is set  
to LOW, the ceramics tips will glow red across 2/3 of each tile. (If the flame continues to lift after 10 minutes or if  
flame remains yellow and sooting occurs, adjust the burner venturi.)  
4. Check that the gas supply is adequate by simultaneously turning on all burners of all appliances connected to the  
same gas supply to their highest setting, then again checking that the broiler’s pilot and burner flames have  
correct appearance and height.  
5. Spread over the hot griddle three or four ounces of beef suet, or as a substitute, baking soda, to season it.  
6. Turn off all burners and allow the broiler to cool.  
STEP 6: WIPE-CLEAN AND SHUT-DOWN APPLIANCE  
1. Wipe clean all surfaces.  
2. Unless the broiler is to be placed in service immediately, shut off the gas supply.  
3. Make sure that a copy of this manual is available to the people who will operate and maintain the broiler.  
OWNERS MANUAL 1190950 (02/09)  
 
PAGE 15 OF 20  
RADIANT STEAKHOUSE BROILER  
SERVICE  
WARNING  
ADJUSTMENTS AND SERVICE WORK MAY BE PERFORMED ONLY BY A QUALIFIED TECHNICIAN WHO IS  
EXPERIENCED IN, AND KNOWLEDGEABLE OF, THE OPERATION OF COMMERCIAL COOKING  
EQUIPMENT. TO ASSURE YOUR CONFIDENCE, CONTACT YOUR AUTHORIZED SERVICE AGENCY FOR  
RELIABLE SERVICE, DEPENDABLE ADVICE OR OTHER ASSISTANCE, AND FOR GENUINE FACTORY  
PARTS.  
NOTICE  
INSTALLATION OF OTHER THAN GENUINE SOUTHBEND PARTS WILL VOID THE WARRANTY ON THIS  
EQUIPMENT.  
The serial plate is located in the rear right corner (see Figure 1 on page 3).  
Replacement parts (including parts not listed in this manual) may be ordered either through a Southbend Authorized  
Parts Distributor or a Southbend Authorized Service Agency.  
When ordering parts, please supply the Model Number, Serial Number, Part Number, and Part Description.  
TROUBLESHOOTING  
Problem  
Look for -  
Not enough heat  
– Low pressure in gas supply  
– Restriction in gas piping and/or valves  
– Misalignment of orifice to burner venturi  
– Clogged burner orifice  
– Incorrect burner orifice  
Too much heat  
– Incorrect orifices  
– Malfunctioning or incorrectly set pressure regulator  
Burner flame has excessive yellow tipping  
– Obstruction of combustion-air intake on rear of broiler  
– Exhaust gases blocked by objects sitting on top of broiler  
– Low pressure in gas supply  
– Misalignment of orifice to burner venturi  
Burner flame fluttering  
Burner flame lifting  
Slow burner ignition  
Pilot outage  
– Low gas pressure or obstruction in orifice  
– High gas pressure or air shutter on venturi out of adjustment  
– Pilot flame out of adjustment  
– Pilot flame out of adjustment  
– Draft condition  
– Pilot orifice clogged  
PAGE 16 OF 20  
OWNERS MANUAL 1190950 (02/09)  
 
RADIANT STEAKHOUSE BROILER  
ACCESS TO SERVICEABLE PARTS  
Some serviceable parts are only accessible by removing body side panels or the burner cover.  
The burner cover is fastened with ten sheet-metal screws. To remove the burner cover, remove these screws. The  
burner cover can then be pulled forward and removed. Each body side panel is fastened with seven sheet-metal  
screws, three in the front and four at the rear. Remove body-side screws and slide the body side towards the rear  
and away from the unit.  
Figure 6  
Access to Serviceable Parts  
Pilot Adjustment  
Screw  
Burner Cover  
Burner Venturi  
Body Side Panel  
ADJUSTMENT OF BROILER PILOTS  
The pilots are adjusted at the factory. If later the pilots are over-adjusted to the point where the flame is leaving its  
port, or “blowing off,” the result is an unstable condition in which the pilot may extinguish. If necessary, adjust the  
pilots using the following procedure:  
1. If necessary, light the pilots.  
2. Locate the pilot adjustment screw (which adjusts all pilots). It is a small slotted screw located on the pilot valve,  
and can be adjusted though an access hole in the burner cover (shown in Figure 6 above).  
3. Turn the pilot adjustment screw to adjust the size of the pilot flames. The flame on each pilot should be large  
enough to extend along the flame carrier to the burner surface.  
OWNERS MANUAL 1190950 (02/09)  
 
PAGE 17 OF 20  
   
RADIANT STEAKHOUSE BROILER  
ADJUSTMENT OF BROILER BURNERS  
The burners are adjusted at the factory. Adjustment may be required to achieve proper operation due to elevation  
change or other variables. Remove the burner cover to adjust the air shutter on each burner venturi (shown in Figure  
6 on the previous page) to achieve proper combustion and optimum burn.  
ADJUSTMENT OF GAS PRESSURE REGULATOR  
The pressure regulator is located at the rear right lower corner of the broiler. The regulator is preset for 6" W.C. for  
natural gas, or 10" W.C. for propane gas. If adjustment is necessary, do the following:  
1. Turn the broiler control knobs to OFF.  
2. Attach a pressure-measuring device to the 1/8" NPT connector located on the main manifold (accessible by  
removing the grease drawer).  
3. Turn the broiler control knobs to HIGH. With the burners lit, check the manifold pressure. The pressure should be  
6" W.C. (for natural gas) or 10" W.C. (for propane gas).  
4. If necessary, adjust the pressure by unscrewing the top of the pressure regulator (use a screwdriver) to expose  
the adjustment screw underneath. Rotating the adjustment screw clockwise increases the manifold pressure.  
5. After the pressure has been adjusted, turn the broiler control knobs to OFF, and replace the top cap of the  
pressure regulator. Disconnect the pressure-measuring device and replace the plug into the manifold.  
PARTS  
The following table describes the serviceable parts. For parts not listed, contact a Southbend Authorized Parts  
Distributor or a Southbend Authorized Service Agency.  
PARTS LIST  
Part Number  
1006436  
NATURAL GAS  
DESCRIPTION  
Quantity  
SSB-32  
SSB-36  
SSB-45  
BURNER ORIFICE  
2
2
2
2
3
3
1176008  
BURNER VALVE  
1184384  
PILOT ADJUST  
1
1
1
1167782  
REGULATOR,PRESS,WC @ 6",NAT  
BURNER, HI-GLOW  
VENTURI ASSEMBLY, HI-GLOW  
CERAMIC TILE  
1
1
1
1130399  
2
2
3
1130398  
2
2
3
1-5371  
20  
2
20  
2
30  
3
1189600  
KNOB  
PARTS LIST  
Part Number  
1006451  
PROPANE GAS  
DESCRIPTION  
Quantity  
SSB-32  
SSB-36  
SSB-45  
BURNER ORIFICE  
2
2
2
2
3
3
1176009  
BURNER VALVE  
1184384  
PILOT ADJUST  
1
1
1
1167783  
REGULATOR,PRESS,WC @10",PROP  
BURNER, HI-GLOW  
VENTURI ASSEMBLY, HI-GLOW  
CERAMIC TILE  
1
1
1
1130399  
2
2
3
1130398  
2
2
3
1-5371  
20  
2
20  
2
30  
3
1189600  
KNOB  
PAGE 18 OF 20  
OWNERS MANUAL 1190950 (02/09)  
 
RADIANT STEAKHOUSE BROILER  
Notes:  
OWNERS MANUAL 1190950 (02/09)  
 
PAGE 19 OF 20  
RADIANT STEAKHOUSE BROILER  
PLATINUM SERIES  
RADIANT STEAKHOUSE BROILER  
Stand Mount, Countertop, Cabinet Base or Refrigeration Base  
A product with the Southbend name incorporates the best in durability and low maintenance. We all recognize,  
however, that replacement parts and occasional professional service may be necessary to extend the useful life of  
this appliance. When service is needed, contact a Southbend Authorized Service Agency, or your dealer. To avoid  
confusion, always refer to the model number, serial number, and type of your appliance.  
Southbend  
1100 Old Honeycutt Road, Fuquay-Varina, NC 27526  
PAGE 20 OF 20  
OWNERS MANUAL 1190950 (02/09)  
 

Silvercrest Blender 600 B26 User Manual
Sony Car Stereo System SCD CE775 User Manual
Sony Clock Radio PEG T615C User Manual
Sony Ericsson Cell Phone J132 User Manual
Star Manufacturing Food Warmer 12MC User Manual
St Bernard Software Webcam v701 User Manual
Sunbeam Electric Heater SFH090 User Manual
Suncast Outdoor Storage BMS7700 User Manual
Superior Gas Heater NEC004 TD User Manual
Superior Modem MD400G User Manual