Sony MP3 Player SEP 30BT User Manual

 
Table of Contents  
About the manuals  
Two manuals, “Operating Instructions” and “Quick Start Guide,” are supplied with this player.  
If you install the supplied software, you can view the softwares help for further information.  
Quick Start Guide  
Explains the basic preparations and operations required to play music and motion.  
Operating Instructions (this manual)  
Explains in detail the preparations and operations required to use the player. You will also  
find troubleshooting advice and precautions on how to use the player safely.  
Rolly Choreographer Help  
Explains how to transfer music from the computer to the player; how to create motion for  
the player and assign it to music; how to customize the player, etc.  
 
Introduction  
Checking the Supplied Accessories  
USB cable (1)  
Rechargeable lithium-ion battery (1)  
CD-ROM* (1)  
Rolly Choreographer software  
* Do not try to play this CD-ROM using a CD music player. It must be read using the CD-  
ROM drive of a computer.  
Stand (1)  
Enjoying not only music but also motion  
The player is a music entertainment player with built-in flash memory, and comes with the  
“Rolly Choreographer” software. You can enjoy listening to music and viewing motion*  
transferred from a computer to the player, using the “Rolly Choreographer” software  
(
page 18).  
* The player moves to the music played. This movement is called “motion” on this player.  
Operating Instructions (this manual) (provided in each language)  
Quick Start Guide (provided in each language)  
Warranty (1 for customers in the USA, 1 for customers in Canada)  
For customers in the USA  
Use “LIMITED WARRANTY” card warranted by Sony Electronics Inc.  
For customers in Canada  
Use “Consumer 1 Year Warranty” card warranted by Sony of Canada Ltd.  
Using the stand  
Listening to music via Bluetooth technology  
When you want to stabilize the player, put the player on the stand.  
Bluetooth® wireless technology is installed in the player. The player works as wireless  
speakers for Bluetooth music players (digital music players, mobile phones, etc.) via a  
Bluetooth connection. You can listen to music stored on Bluetooth music players through  
the speakers of this player ( page 40).  
 
 
Guide to Parts and Controls  
ꢀArmsꢀ(right/left)ꢀ( ꢀpageꢀ11,26,ꢀ  
ꢀBluetoothꢀindicatorꢀ( ꢀpageꢀ42)  
ꢀWheelsꢀ(right/left)ꢀ( ꢀpageꢀ11,ꢀ  
Front  
The blue indicator indicates the Bluetooth  
communication status.  
The arms open while the player is  
playing music. The arms open and close  
repeatedly while the player moves.  
The arms are made to detach in certain  
circumstances for safety reasons.  
By rolling the wheels while playing music,  
you can change volume, tracks, and  
groups. The wheels roll in time to music  
during motion playback.  
Lights up: Not connected  
Flashes once every 0.5 seconds: In the  
process of pairing  
Flashes once every 2 seconds: Waiting for  
connection  
ꢀSpeakers  
ꢀSideꢀlampsꢀ( ꢀpageꢀ26,34)  
Flashes once every 5 seconds: Connected  
The side lamps change colors according  
to playback mode and the status of the  
player. During motion playback, the side  
lamps change colors or flash in time to  
the movement of the player.  
ꢀPlay-buttonꢀindicatorꢀ  
(surroundingꢀtheꢀPlayꢀbutton)ꢀ  
(
ꢀpageꢀ15,ꢀ34)  
The indicator changes color according to  
the status of the player during playback,  
and the status of the battery.  
Light blue: Normal playback  
Purple: Shuffle playback  
Orange: While you can change playback  
mode, or jump tracks/groups  
White: While playing a track with motion  
assigned  
Green: While playing a track without  
motion assigned  
Red: A music file or motion file is  
damaged. Or, excessive mechanical  
load has been applied to the player  
while it is moving.  
Orange: Status of the battery  
Yellow: When charging the battery via a  
USB connection is completed  
Blue: Bluetooth communication status  
ꢀPlayꢀbuttonꢀ( ꢀpageꢀ26,ꢀ33,42)  
ꢀShouldersꢀ(right/left)ꢀ( ꢀpageꢀ26,ꢀ  
Click the Play button to start/stop playing  
music and motion. Use the Play button  
for pairing and connection for Bluetooth  
communication.  
The shoulders move back to the  
predetermined position when the player  
starts playing music. The shoulders move  
around to music during motion playback.  
continued  
 
   
Guide to Parts and Controls (continued)  
When an arm has been detached  
With the shoulder held securely, press  
down the joints (a). Attach the arm (b),  
then close the arm.  
When a wheel has been detached  
Determine the top and bottom sides of the  
wheel. Mount the wheel into the groove of  
the player.  
ꢀResetꢀbuttonꢀ( ꢀpageꢀ49)  
Rear  
You can reset the playback position,  
playback mode, and volume to the default  
settings.  
Even if you press the Reset button, the  
data stored in the player is not erased.  
ꢀBatteryꢀlidꢀ( ꢀpageꢀ12)  
Unfasten the screw and open the battery  
lid. Insert the supplied rechargeable  
battery.  
ꢀUSBꢀjackꢀ( ꢀpageꢀ13)  
When you connect the player to a  
computer, open the cover and plug the  
USB cable into the USB jack.  
ꢀPowerꢀswitchꢀ( ꢀpageꢀ26,34,42,ꢀ  
ON: Power on (to play music and motion)  
OFF: Power off  
: Power on (for Bluetooth  
communication)  
When you turn on the power, the player  
sounds a start-up sound and opens the  
arms once. You can set the player so  
that the start-up sound does not sound  
(
If you leave the player for about 30 seconds  
with the Power switch set to ON or  
the side lamps go off and the player enters  
power-saving mode.  
,
10  
11  
 
   
Charging the Battery  
The player operates on the supplied rechargeable lithium-ion battery (hereinafter called the  
“battery”). When you use the player for the first time, or the battery has been discharged,  
connect the player to a computer to charge it.  
Notes  
Make sure that the battery lid is closed when you operate the player. If the battery lid is open, a  
malfunction may occur.  
When you insert the battery, be careful not to catch your fingers in the battery lid.  
Inserting the battery  
Charging the battery  
1 Turn the battery lid screw to OPEN, using a coin or the like, and open the battery  
lid.  
1 Open the USB jack cover, and connect the supplied USB cable to the USB jack.  
USB jack  
2 Insert the supplied battery all the way in securely, and close the battery lid.  
2 Connect the other end of the USB cable to the USB port of a computer.  
The Play-button indicator lights up in orange, and charging starts. When charging is  
completed, the Play-button indicator turns yellow. Charging will take about 5 hours*.  
(When you charge the battery using the Rolly Charging Cradle CDL-SE10 (not  
supplied), the Play-button indicator goes out when charging is completed. Charging will  
take about 3 hours*.)  
* Expected charging time to charge a fully discharged battery at 25 °C (77 °F). The charging  
time will vary depending on the battery condition or the charging environment.  
3 Turn the battery lid screw to CLOSE, using a coin or the like.  
continued  
1ꢆ  
1ꢇ  
 
   
Charging the Battery (continued)  
Checking the remaining battery power  
Notes  
Set the Power switch to OFF before connecting the player to a computer.  
You cannot operate the player when it is connected to a computer.  
Make sure that you disconnect the player before you turn off or restart your computer.  
Otherwise, the player may not operate correctly.  
Connect the player and the computer directly, not via a USB hub.  
Charge the battery at a temperature ranging from 10 °C (50 °F) to 30 °C (86 °F). Charging may  
not be done efficiently outside of this temperature range.  
In the case of a battery which has been fully discharged or has not been used for a long time,  
the Play-button indicator may not light up immediately after you start charging the battery. The  
Play-button indicator will light up in orange after a few minutes and charging will start.  
When you do not intend to use the player for a long time, remove the battery from the player.  
When the battery is removed, the clock setting and wake-up timer setting will be reset to their  
default settings.  
Set the Power switch to ON or , and hold the player as illustrated on  
the right. The Play-button indicator indicates the remaining battery by  
lighting or flashing.  
You cannot check the remaining battery power when the player is in  
power-saving mode.  
Play-button indicator  
Remaining battery power  
Sufficient  
Lights up in orange for 3 seconds  
Flashes in orange slowly for 3 seconds  
Flashes in orange rapidly for 3 seconds  
Not much left  
Consumed*  
When the battery is fully discharged, the Play-button  
indicator flashes rapidly in orange for 5 seconds. Then, the  
player enters power-saving mode automatically.  
* When the battery is fairly consumed, you cannot play music accompanied by motion.  
continued  
1ꢀ  
1ꢁ  
 
   
Charging the Battery (continued)  
Playback time on the battery (1)  
Notes  
The playback times on the table may differ, depending on surrounding temperatures, operating  
conditions, type of music files, and type of motion.  
The playback times on the table are valid when the player is used at 25 °C (77 °F). The battery  
life will be shorter in lower temperatures, when playing either music or music with motion.  
When you use the player after a long interval, the playback time may be shorter than expected,  
because the battery cannot yet be charged to its full capacity. After the battery is fully  
discharged and charged several times, it can be charged to its full capacity.  
Playing  
Music (2)  
Music with motion (2)(3)  
Playback time (approx.)  
5 hours  
4 hours  
Music via Bluetooth communication  
Music with motion via Bluetooth communication (3)  
4 hours 30 minutes  
3 hours 30 minutes  
If the playback time becomes about half of the normal length of time, even if it is charged  
sufficiently, the useful life of the battery has run out. Replace the battery with a new one.  
(1)  
Measured using a fully charged battery  
(2)  
Playback time of music is measured using MP3 128 kbps music.  
(3)  
Playback time of motion is measured using a Sony standard motion measurement (equivalent to the  
Auto motion) and operating environment. Motion playback stops after 1 track. You cannot continue  
playing tracks together with motion.  
1ꢂ  
1ꢃ  
 
   
Enjoying Music and Motion  
The player plays music and motion transferred from a computer, using the supplied “Rolly  
Choreographer” software.  
Installing the  
software (page 20)  
Transferring music  
and motion to the  
Playing music and  
1ꢄ  
1ꢅ  
 
 
Installing the Software  
Install the supplied “Rolly Choreographer” software. See page 21 for the system  
requirements that must be met to use the player.  
System requirements for the player  
Computer  
Turn on the computer and start Windows.  
Computer:  
1
Log on as an administrator.  
IBM PC/AT or compatible computer preinstalled with the following Windows operating  
systems.  
Quit all active software programs on your computer.  
Be sure to quit all software programs, including anti-virus software, as they will strain  
the CPU.  
Windows XP Home Edition (Service Pack 2 or later)/Windows XP professional (Service  
Pack 2 or later)/Windows XP Media Center Edition (Service Pack 2 or later)/Windows XP  
Media Center Edition 2004 (Service Pack 2 or later)/Windows XP Media Center Edition  
2005 (Service Pack 2 or later)/Windows Vista Home Basic/Windows Vista Home Premium/  
Windows Vista Business/Windows Vista Ultimate  
Insert the supplied CD-ROM into your computers CD-ROM drive.  
The install wizard will start automatically and the Main Menu appears.  
Not supported by operating system other than those listed above.  
Not supported by 64 bit versions of the operating systems listed above.  
Install the software.  
Operating system language supported: English and French  
Read the message displayed on the screen carefully, and follow the on-screen  
instructions. Installation may take 10 to 15 minutes depending on your computer. If  
prompted, restart the computer after installing the software.  
CPU: Pentium III 450 MHz or higher (For Windows Vista, Pentium III 800 MHz or higher)  
RAM: 256 MB or more for Windows XP (512 MB or more is recommended.)  
512 MB or more for Windows Vista (1 GB or more is recommended.)  
Video memory: 64 MB or more  
Hard Disk Drive: 200 MB or more of available space (1.5 GB or more is recommended.)  
More space may be required depending on the version of the operating system. Additional  
space is required for storing music data.  
When the software has been installed successfully, an  
computer screen.  
icon appears on the  
Note  
If the Windows Aero function of Windows Vista is activated, the preview area of Rolly  
Choreographer may not appear properly.  
Display: 1024 × 768 pixels (or higher), High Color (16 bit) (or higher) (Rolly Choreographer  
may not operate properly at color settings at or below 256 colors.)  
CD-ROM drive: Must support Digital Music CD playback capabilities using WDM.  
(To create original CDs or to back up audio CDs, a CD-R/RW drive is required.)  
Sound board  
Deactivate the Windows Aero function when starting Rolly Choreographer as follows.  
1 Right-click the Rolly Choreographer icon, display “Properties” and click the “Compatibility”  
tab.  
2 Check “Disable desktop composition” and click [OK].  
USB port (Hi-Speed USB is recommended.)  
continued  
ꢆ0  
ꢆ1  
 
   
Installing the Software (continued)  
Transferring Music and Motion to the Player  
Microsoft Internet Explorer 5.5 or later must to be installed.  
An internet connection is required to upload/download motion data.  
We do not guarantee operation for all computers, even if they meet the above System  
Requirements.  
The Automatic Choreography & Transfer” function enables you to transfer music and  
motion data to the player simply by pressing the  
screen.  
button on the Rolly Choreographer  
You select tracks and press the  
button. Then, the tracks are transferred to the player.  
Not supported by the following environments:  
The transferred tracks are choreographed with the appropriate motion by the Automatic  
Choreography” function.  
Personally constructed PCs or operating systems/An environment that is an upgrade of the  
original manufacturer-installed operating system/Multi-boot environment/Multi-monitor  
environment/Macintosh  
PC tree  
We do not guarantee correct operation for all computers on which system suspension, sleep  
(standby), hibernation, etc. are operating correctly.  
PC list  
Uninstalling the software  
To delete the supplied software from your computer, perform the following steps.  
1 Click [Start] - [Control Panel].  
2 Double-click [Add or Remove Programs].  
3 Select Rolly Choreographer from the list, and click [Delete].  
Restart the computer following the on-screen instructions. When the computer is  
restarted, the software has been uninstalled.  
USB cable (supplied)  
Connect the player to the computer using the supplied USB cable.  
1
Click the  
icon on the screen.  
Rolly Choreographer will start and the File Manager View will appear.  
continued  
ꢆꢆ  
ꢆꢇ  
 
   
Transferring Music and Motion to the Player (continued)  
For details, refer to the Rolly Choreographer Help.  
To transfer all music files in a folder, select the folder in the PC tree.  
Hints  
To transfer a single file, select the file in the PC list.  
The player plays the transferred tracks in the order of tracks displayed on Rolly Choreographer.  
The player can play up to 4,096 tracks.  
You can select more than one file to be transfered at one time.  
You can transfer tracks without accompanying motion. Select the folder or file, and press the  
button. You can assign motion to tracks after they have been transferred to the player. For  
details, refer to the Rolly Choreographer Help.  
You can transfer music to the player using Windows Explorer or other music management  
software. When you use any software other than Rolly Choreographer, place the data in the  
“MUSIC” folder.  
Press the  
button.  
The selected folder or file will be transferred. Each track will be transferred with  
motion created automatically by the Automatic Choreography” function.  
If the track has a motion assigned, the track is transferred to the player with the  
motion.  
The player can play .mp3” and .3gp*” music files only. The player cannot play .m4a” and  
.mp4” music files. To make .m4a” and .mp4” music files in a computer playable on the player,  
transfer them by using Rolly Choreographer. .m4a” and .mp4” music files will be converted to  
.3gp” music files automatically, and transferred to the player.  
You can create and edit motion as you like on Rolly Choreographer. You can also change the  
settings of the player. For details, see the Rolly Choreographer Help.  
You can create motion and upload their data to the service site on the internet, or download  
motion data from the service site and store them in Rolly Choreographer. For details, see the  
Rolly Choreographer Help.  
When deleting transferred music  
Make sure that you delete music files from the player using Rolly Choreographer.  
Notes  
Set the Power switch of the player to OFF before connecting the player to a computer.  
The Play-button indicator flashes while music and motion are being transferred. Leave the USB  
cable connected during this period.  
If you delete music files from the player, the motion instruction assigned to the music will also  
be deleted.  
If you connect the player to a lap-top computer that is not connected to AC power sources,  
the battery of the lap-top computer will be consumed quickly. Do not leave the player and the  
lap-top computer in this state for a long time.  
* HE-AAC codec .3gp” files or movie .3gp” files cannot be played on the player.  
Music tracks transferred to the player with Rolly Choreographer are saved in the “RMF” folder  
on the player and displayed in the Rolly list with Rolly Choreographer. Do not add or delete  
files in the “RMF,RSF,or “SMDB” folder on the player with Windows Explorer, and also do  
not delete or rename these folders with Windows Explorer. If you do so, some music tracks may  
not be displayed in the Rolly list and they may not be played on the player.  
ꢆꢀ  
ꢆꢁ  
 
 
Playing Music  
You can play music transferred from a computer using Rolly Choreographer.  
Two ways to operate the player  
You can play motion together with music ( page 33).  
You can operate the player either placed on a level surface or held in your hand as shown  
below.  
Play button  
Play-button indicator (surrounding the Play button)  
Power switch  
When the player is placed on a  
level surface  
When you hold the player in your  
hand  
Side lamps  
Set the Power switch to ON.  
1
The start-up sound sounds and the power is turned on.  
Place the player on a stable surface with the SONY logo facing you.  
Click the Play button.  
The player opens its arms and plays music.  
The Play-button indicator lights up during playback. The indicator changes color  
according to whether a motion is assigned to the track or not ( page 34).  
Place the player with the SONY logo facing Hold the player in the vertical position.  
you. Operate the player by pushing the Operate the player by turning the wheels to  
player on the wheels while music is playing. the right or left while music is playing.  
To stop playing music  
Click the Play button during playback. The player stops playing music and closes its arms.  
continued  
ꢆꢂ  
ꢆꢃ  
 
   
Playing Music (continued)  
Changing a track  
(1)  
(2)  
* When you hold the player in the vertical  
position with either end at the top, the  
wheel at the top is automatically assigned  
to changing tracks/groups.  
If you try to return to the previous track  
after more than 5 seconds have elapsed  
since the track started, the current track  
will be played from the beginning.  
When you perform this operation on the  
first track of the group:  
If you try to return to the previous group  
after more than 5 seconds have elapsed  
since the playback started, the current  
track will be played from the beginning.  
When you perform this operation on the  
second or a later track of the group:  
The first track of the group will be played  
from the beginning.  
To locate the beginning of the  
To locate  
the previous  
track/group  
To locate the next  
track/group  
next track/group  
To locate the beginning of  
the previous (or current)  
track/group  
To change the track, turn the upper  
wheel* about 45° while music is playing.  
The operation sound sounds and the track  
changes.  
To change the music group, turn the upper  
wheel about 90°. The operation sound  
sounds, the group number is announced,  
such as “Group One,” and the group  
changes.  
Playback starts from the loudest point of  
the track. When you place the player on  
a level surface, playback starts from the  
beginning of the track.  
To change the track, push the player  
forward or backward a short distance  
while music is playing. The operation  
sound sounds and the track changes.(1)  
To change the music group, push the  
player forward or backward further.  
The operation sound sounds, the group  
number is announced, such as “Group  
One,” and the group changes.(2)  
continued  
ꢆꢄ  
ꢆꢅ  
 
 
Playing Music (continued)  
Adjusting the volume  
Shuffle playback  
You can switch the playback mode (normal playback or shuffle playback). Hold the player  
in your hand to switch the playback mode.  
1 While music is playing, double-click the Play button.  
The side lamps light up in orange.  
To turn down  
the volume  
To turn up the  
volume  
2 While the side lamps are lit in orange, shake the player up and down a few times.  
The operation sound sounds and the side lamps turn purple. The playback mode  
switches to shuffle mode.  
A different track will start and all tracks stored on the player will be played in random  
order.  
To turn down the volume  
To turn up the volume  
While music is playing, turn the lower  
wheel* to the right to turn up the volume,  
and to the left to turn it down.  
While music is playing, rotate the player  
clockwise to turn up the volume, and  
counterclockwise to turn it down.  
The player returns automatically to the  
position it was before the volume was  
adjusted.  
* When you hold the player in the vertical  
position with either end at the top, the  
wheel at the bottom is automatically  
assigned to controlling the volume.  
You can set the player not to return to  
the position it was before the volume was  
adjusted ( page 37).  
To return to normal mode, perform steps  
1 and 2 again.  
The operation sound sounds, the side  
lamps turn light blue. The playback mode  
switches to normal mode.  
continued  
ꢇ0  
ꢇ1  
 
   
Playing Music (continued)  
Making the Player Move to Music  
You can play motion transferred from Rolly Choreographer in time to music.  
When the music has no motion assigned, the player analyzes the music, then creates and  
assigns motion appropriate to the music (“self-motion” function).  
Jumping 5 tracks/groups ahead (or back)  
Hold the player in your hand to jump tracks/groups.  
“Motion playback” is available only when the player is placed on a level surface.  
1 While music is playing, double-click the Play button.  
The side lamps light up in orange.  
Restrictions on motion playback  
2 While the side lamps are lit in orange, turn the upper wheel.  
Motion playback of the player was designed taking safety into consideration. Motion  
playback has the following restrictions to prevent the player from falling off a table or desk,  
or colliding against other objects, or to avoid accidents when you take your eyes away from  
the player.  
If you turn the wheel to the right (left) about 45°, you can jump 5 tracks ahead (back).  
If you turn the wheel to the right (left) about 90°, you can jump 5 groups ahead (back).  
Hint  
Motion stops when a track is over.  
You can set the start-up sound, operation sound, and verbal guide for the group number so they  
do not sound using Rolly Choreographer (page 37).  
You cannot operate the player other than stopping during motion playback.  
A motion can play no longer than 7 minutes per track. This is the same for either motions  
created by Rolly Choreographer or “self-motions.” When the track is longer than 7 minutes, the  
player plays music and motion for the first 7 minutes, and music only for the rest of the track.  
Notes  
If you leave the player with the Power switch set to ON for about 30 seconds, the player enters  
the power-saving mode automatically to save battery power. You can set the player to power-  
saving mode by holding the Play button down for about 2 seconds. To release power-saving  
mode, click the Play button.  
If you play music near the range of maximum volume level, the speakers vibrate, and the case of  
the player vibrates, too. If the arms close (in the course of a motion procedure, or are closed by  
hand), the sound may be muffled or distorted.  
Places to perform motion playback  
Perform motion playback on a spacious level surface without obstacles around.  
Avoid the following places or surfaces when performing motion playback.  
Where there is a risk that the player may drop  
Uneven places, or unstable places subject to vibrations  
Slippery places, or on thick carpet  
Soft surfaces, such as bedding  
Places subject to soil, sand, or dust  
Wet places with water or oil present  
Outdoors  
continued  
ꢇꢆ  
ꢇꢇ  
 
   
Making the Player Move to Music (continued)  
Play button  
To stop motion  
Play-button indicator (surrounding the Play button)  
Power switch  
When you want  
Operation  
To stop motion only, and continue playing music Hold the player in the vertical position. After  
motion stops, place the player on a level surface.  
Side lamps  
To stop motion only, and play music from the  
beginning of the track  
Double-click the Play button.  
Set the Power switch to ON.  
A starting sound sounds and the power is turned on.  
To stop both motion and music  
Click the Play button once.  
1
Place the player with the SONY logo facing you.  
Hints  
You can switch to motion playback by double-clicking the Play button while music is playing.  
The currently played track will be played again from the beginning together with motion.  
For creating motion using Rolly Choreographer, refer to the Rolly Choreographer Help.  
Double-click the Play button.  
The player plays music and motion.  
The Play-button indicator changes color according to the playback status.  
White: Playing music with motion assigned.  
Green: Playing music without motion assigned. The player analyzes the music, and  
moves appropriately to the music automatically (“self-motion” function).  
Orange: The player cannot play motion because there is not enough battery  
remaining.  
When playback of a track is finished, motion stops. Only music will be played from  
next track.  
continued  
ꢇꢀ  
ꢇꢁ  
 
   
Making the Player Move to Music (continued)  
Customizing the Player  
Using the [Tools] menu of the supplied Rolly Choreographer software, you can customize  
or reset the player’s performance. Refer to the Rolly Choreographer Help for details on the  
setting operations required.  
Notes  
If you hold the arms and wheels down, or try to stop motion in any way during motion  
playback, the side lamps will light up in red and motion stops.  
If you play music near the range of maximum volume level, the speakers vibrate, and the case of  
the player vibrates, too. If the arms close (in the course of a motion procedure, or are closed by  
hand), the sound may be muffled or distorted.  
Motions are reproduced differently depending on the location or surface where the player is  
used.  
Motions actually reproduced by the player (such as fine movements, slow movements, sudden  
starts, sudden stops, spinning) may differ from those same motions previewed on Rolly  
Choreographer.  
Items  
Set-ups  
Rolly  
Settings  
Operation  
Sound  
You can set whether to sound the following 3 kinds of sounds or  
not. Sounds are set to sound as the default setting.  
Startup Sound Setting: This sounds when the power is turned  
on, or as an alarm when required.  
Operation Sound Setting: This sounds when tracks are  
forwarded/reversed, groups are forwarded/reversed, or  
playback mode is changed.  
Group Voice Guidance Setting: When you change groups, the  
selected group number is announced.  
Motions assigned to MP3 variable bit rate format files may not be played correctly.  
Volume  
Operation  
You can set the player to return automatically to the position it  
was before the volume was adjusted, when the player was placed  
on a level surface. This item is set to return to original position as  
the default setting.  
Bluetooth  
You can select the priority, whether for sound quality or  
Communication communication stability, for Bluetooth communication.  
Communication stability is given the priority as the default  
setting.  
In addition, you can employ the SCMS-T content protection  
of the Bluetooth device connected to the player. If the music  
transferred from the Bluetooth device connected is not  
compatible with the SCMS-T content protection standard,  
deactivate the SCMS-T content protection.  
continued  
ꢇꢂ  
ꢇꢃ  
 
     
Customizing the Player (continued)  
Using the wake-up timer  
Items  
Set-ups  
When you set the wake-up timer on, disconnect the USB cable from the player, and leave  
the Power switch to ON.  
If the player is playing music at the preset time, the wake-up function does not work.  
To check whether the wake-up timer is set to on or not, set the Power switch to ON and  
hold the Play button down for about 2 seconds. When it is set to on, the Play-button  
indicator flashes 3 times in green.  
Rolly  
Wake-up Timer  
You can set the player to start at a preset time and play a preset  
music item automatically. If you leave this setting on, the player  
starts and plays music at a preset time everyday.  
Settings  
Device  
Information  
You can check the player’s version and memory capacity (used  
and free).  
Initialize  
Rolly  
Settings  
You can initialize the player to the default settings. The stored  
music and motion data are retained.  
Hint  
When the player is connected to a computer and Rolly Choreographer is running, the clock  
Format  
Rolly  
You can format the built-in flash memory of the player. The  
stored music and motion data are all erased. Before formatting  
the player, check the contents, and save any important music and  
motion data on your computer using Rolly Choreographer.  
function of the player is synchronized with the clock of the computer.  
Notes  
The track used for the wake-up timer is remembered by the order of the track, not by the name  
of the track. Therefore, if you delete the track or change the order of tracks, you will hear a  
different track.  
You can check the preset track on the Rolly screen of Rolly Choreographer. The preset track will  
be displayed with an orange clock mark on the title list.  
Note  
Make sure that you format the player using this “Format Rolly”  
on Rolly Choreographer. Never format the player using Windows  
Explorer. If you do so, the player will not be recognized by the  
computer.  
You cannot play motion for the wake-up timer.  
Initializing or formatting the player  
Initializing and formatting operations require a fully charged battery. Before initializing or  
formatting the player, fully charge the battery.  
continued  
ꢇꢄ  
ꢇꢅ  
 
 
Listening to Music via Bluetooth Communication  
The player works as wireless speakers for Bluetooth music players (digital music players,  
mobile phones, etc.). You can enjoy music data stored on Bluetooth music players through  
the speakers of this player.  
Bluetooth devices must support the A2DP profile to be connected with the player. In  
addition, when the devices also support the AVRCP profile, you can operate those devices,  
such as starting and stopping playback, with this player.  
You can find Bluetooth music players that can be connected with this player at the website  
below.  
See page 66 for details on Bluetooth wireless technology.  
Note  
For customers in Canada:  
You cannot listen to music played on this player through headphones or speakers of Bluetooth  
devices.  
Pairing the devices  
Connecting the  
devices (page 44)  
Listening to music  
ꢀ0  
ꢀ1  
 
   
Pairing the Player with a Bluetooth Device  
Pairing is an operation where Bluetooth devices register with each other.  
Once you pair the player with a Bluetooth device, you do not need to repeat the pairing  
operation with the Bluetooth device again, except for the following occasions:  
The pairing information is erased from the player, due to, for example, repair.  
You pair the player with a 9th Bluetooth device. The player can be paired with up to  
8 Bluetooth devices. If you pair the player with another Bluetooth device, the pairing  
information of the Bluetooth device that has not been connected for the longest time  
among the 8 Bluetooth devices will be replaced by the pairing information of the new  
Bluetooth device.  
Hold the Play button of the player down for more than 7 seconds.  
While the player is processing the pairing, the Bluetooth indicator flashes rapidly in  
blue.  
Note  
The pairing process lasts about 5 minutes. If the process is interrupted before you complete  
operations up to step 4, perform operations from step 2 again.  
Perform the pairing operation on the Bluetooth device to be paired, and  
search for the player.  
For details about the pairing operation, refer to the operation manual supplied with  
the Bluetooth device to be paired.  
The connection information for the player was deleted from the connected Bluetooth  
device.  
When you initialize or format the player using Rolly Choreographer, pairing information  
with all Bluetooth devices will be erased.  
If the Bluetooth device to be paired has a display, perform the following steps:  
When a list of the devices found appears, select “SEP-30BT.” If “SEP-30BT” is not  
displayed, perform operations from step 1 again.  
Bluetooth indicator  
When a passcode* is required, enter “0000” (zero-zero-zero-zero).  
* “Passcode” may be called “Passkey,” “PIN code,” “PIN number,” or “Password,” etc.,  
depending on the device.  
Play button  
Power switch  
When pairing is successful, the Bluetooth indicator of the player will flash slowly.  
Place the Bluetooth device to be paired within 1 m (3 feet) of the player.  
Note  
1
When pairing is unsuccessful, the Bluetooth indicator does not flash slowly. If the Bluetooth  
indicator flashes rapidly in blue, perform step 4 again. If the Bluetooth indicator lights up  
and remains lit, perform operations from step 2 again.  
Set the Power switch of the player to  
.
An operation sound sounds, and the Bluetooth indicator ( page 9) lights up in blue.  
Interrupting the pairing operation  
Hold the Play button down for about 2 seconds.  
ꢀꢆ  
ꢀꢇ  
 
   
Connecting the Player and the Bluetooth Device  
After pairing has been completed successfully, establish a Bluetooth connection between  
the player and the paired Bluetooth device.  
Note  
A Bluetooth connection is cleared in the following cases.  
The player is turned off.  
The paired Bluetooth device or its Bluetooth function is turned off.  
The player or the Bluetooth function of the Bluetooth device is set to sleep mode.  
The Bluetooth connection is disconnected.  
You must connect the player and the paired Bluetooth device again as described on the previous  
page.  
Depending on the Bluetooth device used, a Bluetooth connection is automatically  
established after pairing has been completed successfully.  
Activate the Bluetooth function of the paired Bluetooth device so that  
1
the device can be connected with the player.  
For details about the operations of the paired Bluetooth device, refer to the operations  
manual supplied with the Bluetooth device.  
Set the Power switch of the player to  
.
Click the Play button of the player.  
The flashing intervals of the Bluetooth indicator change as follows, and the  
connection between the player and the paired Bluetooth device is established.  
Flashes once every 2 seconds (The connection is being processed.)  
Flashes once every 5 seconds (The connection has been established.)  
When the connection is established, the player opens its arms once.  
If the connection has not been established, perform the connecting operation on the  
paired Bluetooth device.  
For details about the operation of the paired Bluetooth device, refer to the operations  
manual supplied with the Bluetooth device.  
ꢀꢀ  
ꢀꢁ  
 
   
Listening to Music  
When the connection between the player and the paired Bluetooth device is established,  
you can listen to music played on the paired Bluetooth device through the speakers of the  
player, by operating either the player or the paired Bluetooth device.  
Notes  
When Bluetooth devices other than the player are connected to the paired Bluetooth device,  
the music played on the Bluetooth device may sound only intermittently through the speakers  
of the player. If this happens, disconnect the other Bluetooth devices from the paired Bluetooth  
device.  
If you play movies on the paired Bluetooth device, there may be a lag in audio playback, due to  
the performance of Bluetooth function.  
If you play music near the range of maximum volume level, the speakers vibrate, and the case of  
the player vibrates, too. If the arms close (in the course of a motion procedure, or are closed by  
hand), the sound may be muffled or distorted.  
Click the Play button of the player.  
1
If the paired Bluetooth device does not support the AVRCP profile, perform playback  
operations on the paired Bluetooth device.  
The paired Bluetooth device starts playback.  
The Play-button indicator of the player lights up in green during playback.  
Adjust the volume on the player.  
If you cannot increase the volume by operating the player, try on the paired Bluetooth  
device.  
Hints  
You can make the player move appropriately to the music played on the paired Bluetooth  
device. Double-click the Play button while music is playing. The motion starts when you  
double-click the button.  
When the paired Bluetooth device supports the AVRCP profile, and the AVRCP function is  
activated, you may be able to stop playback, and change tracks/groups by operating the player.  
For details, refer to the operations manual supplied with the Bluetooth device.  
When the paired Bluetooth device supports AVRCP VOLUME UP/DOWN, you can adjust the  
volume of the player on the paired Bluetooth device. For details, refer to the operations manual  
supplied with the Bluetooth device.  
ꢀꢂ  
ꢀꢃ  
 
   
Updating the Firmware  
Troubleshooting  
By installing the latest firmware, you can add new functions and features to the player.  
For details on the latest firmware and the updating method, visit the website below.  
For customers in the USA:  
If the player does not function as expected, try the following steps to resolve the problem.  
1 Find the symptoms of the problem in the following troubleshooting tables, and  
try the corrective actions listed.  
2 Press the Reset button with a small pin or the like.  
For customers in Canada:  
Even if you press the Reset button, stored music and motion data are retained. However,  
playback settings (volume, stop position, normal/shuffle playback, etc.) may be reset to  
the default setting.  
Download the update program to your computer from the home page of  
3 Check for information about the problem in Rolly Choreographer.  
1
the Rolly customer support.  
4 Look for information about the problem on the website below.  
Connect the player to your computer, and start the update program.  
For customers in the USA:  
For customers in Canada:  
Follow the instructions of the update program.  
The firmware will be updated.  
5 If the approaches listed above fail to resolve the problem, consult your nearest  
Sony dealer or Sony Service Center.  
continued  
ꢀꢄ  
ꢀꢅ  
 
   
Troubleshooting (continued)  
Playing music/motion  
Symptom  
Cause/Remedy  
The side lamps light up in red, and  
motion is not played.  
Movable parts (arms, wheels) have been tucked in or have  
collided against something.  
Symptom  
Cause/Remedy  
Buttons do not work.  
The player contains moisture condensation.  
Wait for a few hours to let the player dry.  
Free the movable parts from obstacles. When the side  
lamps go out, double-click the Play button. The player  
will start playing motion.  
The remaining battery power is low or insufficient.  
Charge the battery sufficiently ( page 12)  
The music or motion file is damaged.  
If nothing happens after you charge the battery  
The Play-button indicator flashed,  
and music playback stopped  
automatically.  
If heat is built up in the player, the player stops playback  
automatically, and enters power-saving mode.  
sufficiently, press the Reset button to reset the player  
(
page 49).  
Repeat inserting and removing the battery several times.  
The Play-button indicator flashed,  
and motion playback stopped  
automatically.  
If heat is built up in the player, the player stops playing  
Playback does not start even if you  
click the Play button.  
The Power switch is set to OFF.  
motion automatically, and continues playing music only.  
Set the Power switch to ON.  
There is no sound.  
The volume may be set to the minimum. Adjust the  
The left and right shoulders are out  
of position.  
The shoulders may come out of position depending on the  
circumstances where the player is used. For a remedy, visit  
the website below.  
volume ( page 30).  
Noise is generated.  
A device emitting radio sounds, such as a mobile phone, is  
being used near the player.  
When using devices such as mobile phones, keep them  
away from the player.  
For customers in the USA:  
For customers in Canada:  
Motion is not played.  
The remaining battery power is insufficient.  
Charge the battery sufficiently ( page 12)  
The assigned motion does not involve movement.  
Check the motion data on Rolly Choreographer.  
You click the Play-button only once.  
The player gets warm.  
The player gets warm during operation. This is normal  
and not cause for concern.  
Motion and side lamps do not act  
according to the motions created  
using Rolly Choreographer.  
Due to the characteristics of the player, motion and side  
lamps may act differently from those same motions  
created using Rolly Choreographer.  
Double-click the Play-button.  
The side lamps light up in red, and  
the player skips the track you want to  
listen but plays the next track.  
The music or motion file is damaged.  
continued  
ꢁ0  
ꢁ1  
 
Troubleshooting (continued)  
Symptom  
Cause/Remedy  
Symptom  
Cause/Remedy  
There is sufficient remaining battery  
power, but playback cannot be done.  
The battery has deteriorated and should be replaced.  
Consult your nearest Sony dealer or Sony Service  
Center.  
Even if you started charging the  
battery, the Play-button indicator  
does not light up in orange.  
When the battery is discharged entirely, or has not been  
used for a prolonged period, the indicator may not light  
up immediately after the charging preparations are  
completed. After a few minutes, the indicator will light up  
in orange and charging of the battery will start.  
Some music tracks cannot be played.  
If you add or delete files in the “RMF,RSF,or “SMDB”  
folder on the player, or delete or rename these folders,  
some music tracks may not be displayed in the Rolly list  
on Rolly Choreographer and they may not be played on  
the player.  
Computer connection/Rolly Choreographer  
Symptom  
Cause/Remedy  
When you install the software,  
an error message appears on the  
computer display.  
You may not be able to use the player with that computer.  
Charging the battery  
See the system requirements ( page 21).  
Symptom  
Cause/Remedy  
Battery life is short.  
The operating temperature is below 5 °C (41 °F).  
Battery life sometimes becomes shorter due to the  
circumstances in which the battery is being used. This is  
not a malfunction.  
Even if you insert the supplied CD-  
ROM into the computer, the install  
wizard does not start automatically.  
The install wizard may not start even if the CD-ROM is  
inserted, depending on the computer setting. In this case,  
right-click the CD-ROM drive on Windows Explorer,  
double-click SetupSS.exe. The Main Menu for installation  
will appear.  
Battery charging time is not sufficient.  
Charge the battery sufficiently.  
Rolly Choreographer cannot be  
installed.  
Visit the website below.  
You have not used the player for a prolonged period.  
The efficiency of the battery will be recovered by  
repeatedly charging and discharging it.  
The battery should be replaced with a new one.  
Consult your nearest Sony dealer or Sony Service  
Center.  
For customers in the USA:  
For customers in Canada:  
The battery is not charged.  
The USB cable is not connected to a USB port on your  
computer properly.  
Disconnect the USB cable, and then connect it again.  
Use the supplied USB cable.  
continued  
ꢁꢆ  
ꢁꢇ  
 
Troubleshooting (continued)  
Symptom  
Cause/Remedy  
Symptom  
Cause/Remedy  
The computer does not recognize  
the player.  
The USB cable is not connected to the USB port of the  
computer securely.  
Disconnect the USB cable, and then connect it again.  
Try other USB ports of the computer.  
There is no battery in the player.  
Insert the battery.  
The sound is heard intermittently.  
There are obstacles (metal objects, persons, walls, etc.)  
between the player and the paired Bluetooth device.  
Avoid or remove the obstacles.  
If there is equipment that generates electromagnetic  
radiation, such as a wireless LAN, other Bluetooth device,  
or a microwave oven nearby, move them away.  
If Bluetooth devices other than the player are connected  
to the paired Bluetooth device, the music played on the  
Bluetooth device may sound intermittently through the  
speakers of the player. If this happens, disconnect the  
other Bluetooth devices from the paired Bluetooth device.  
Bluetooth communication  
Symptom  
Cause/Remedy  
The sound of the connected  
Bluetooth device is not heard.  
The sound is silenced on the paired Bluetooth device.  
Turn up the volume on the paired Bluetooth device.  
The volume may be set to the minimum.  
A connection cannot be established.  
The Bluetooth device to be connected does not support  
the SCMS-T system.  
On the [Tools] menu of Rolly Choreographer, select  
[Rolly Settings] - [Bluetooth Communication]  
- [Copyright Protection] - [Copyright Protection]  
- [Disable SCMS-T method content protection].  
Adjust the volume ( page 30).  
Noise is generated.  
Noise may be generated depending on the environment  
in which the connection with the Bluetooth device was  
established.  
Try establishing the connection with the Bluetooth  
device again.  
Others  
Symptom  
Cause/Remedy  
Pairing cannot be done.  
The player is too far from the Bluetooth device to be  
paired.  
The arm was detached.  
The wheel was detached  
Attach the arm as described on page 11.  
Attach the wheel as described on page 11.  
Place the player and the Bluetooth device closer and  
perform the pairing operation.  
Make sure that the paired Bluetooth device supports the  
A2DP profile.  
ꢁꢀ  
ꢁꢁ  
 
Precautions  
On safety  
On places the player can be used  
Be sure not to short-circuit the terminals of the player with other metallic objects.  
Do not touch the rechargeable battery with bare hands if it is leaking. Since battery liquid may  
remain in the player, consult your nearest Sony dealer or Sony Service Center if the battery  
has leaked. If the liquid gets into your eyes, do not rub your eyes as this may lead to blindness.  
Wash out your eyes with clean water, and consult a doctor immediately.  
Also, if the liquid gets on to your body or clothes wash it off immediately. If you do not, it may  
cause burns or injury. If you get burned or injured by the liquid from the battery, consult a  
doctor.  
The player operates in temperatures ranging from 5 °C (41 °F) to 35 °C (95 °F). It is not  
recommended to use the player in extremely cold or hot places out of this temperature range.  
Do not use the player in a location where the player may drop or fall from a table or desk. Use  
the player on stable, flat, and level surfaces.  
Do not use the player on a hard and rough floor, such as a concrete floor, and the like. This kind  
of floor may mar the player, and cause a malfunction.  
Do not use the player on a slippery floor, thick carpet, or where the player may catch in hairs,  
etc. On such floors, the wheels of the player tend to catch in the carpet, etc. As a result, the  
player may malfunction and may not be reparable.  
Do not pour water on or put any foreign object into the player. Doing so may cause fire or  
electric shock.  
Avoid the following places. These places may cause a malfunction of the player.  
If this occurs, turn off the player immediately, disconnect the USB cable from the player, and  
consult your nearest Sony dealer or Sony Service Center.  
Soft surfaces, such as bedding  
Places subject to soil, sand, or dust  
Do not put the player into a fire.  
Wet places with water or oil present  
Do not take apart or remodel the player. Doing so can result in electric shock. Consult your  
nearest Sony dealer or Sony Service Center for exchange of rechargeable batteries, internal  
checks, or repair.  
Outdoors  
Make sure that you let the player move where there is no risk that the player can drop or fall,  
and where there are no obstacles around. Keep the player out of reach of children. Even if  
the player or surrounding objects are damaged because the player drops or collides against  
obstacles or children, Sony is exempt from any responsibility.  
continued  
ꢁꢂ  
ꢁꢃ  
 
 
Precautions (continued)  
On handling the player  
On moisture condensation  
If the player is brought directly from a cold place to a warm place, moisture may condense  
on the surface or inside of the player. This may cause a malfunction of the player. If moisture  
condensation has occurred, leave the player for about 2, 3 hours without turning it on.  
Do not apply excessive force to the player, for example, by grabbing or stepping on the player.  
Do not apply shock to or drop the player. The stored data may be erased, or a malfunction may  
occur.  
Do not touch the charging terminal directly with your hands. The contact will be affected.  
Do not hold or swing the player by the arms. Do not twist the arms.  
Do not leave the player exposed to high temperature, such as in a car parked in the sun or  
under direct sunlight.  
Do not interrupt the movement of the player forcibly.  
Do not oil the movable parts (arms, wheels).  
On handling the battery  
Do not leave the battery in a location with temperatures above 60 °C (140 °F). This may cause  
deterioration or a malfunction of the battery.  
When the player is warm, the battery is also warm. Handle them with care.  
Keep the terminals free from dust and any other foreign objects.  
When you do not intend to use the player for a long time, remove the battery from the player.  
Store the battery in a dry place in temperatures ranging from 0 °C to 30 °C (32 °F to 86 °F) to  
maintain the battery capability.  
The battery is discharged automatically even if it is not used. It is recommended that you charge  
the battery again before using it.  
Do not drop the battery, or put heavy objects on top of it. Do not apply a strong shock or  
pressure to the battery.  
The battery has a limited life-span. The battery capacity decreases gradually over time and  
repeated use. If usable battery time becomes significantly short, you should replace the battery  
with a new one. Consult your nearest Sony dealer or Sony Service Center. The battery life  
depends on storage, operating, and environmental conditions.  
Do not limit the movement of the player by adhering stickers, tying on ribbons, or tucking  
something behind the movable parts.  
When you carry the player, put the player in the Rolly soft carrying case (not supplied), or a box  
made of shock-absorbing material like the package which the player comes in, so that the arms  
and other parts are free from strain.  
Do not touch the speakers directly with the fingers. This may cause a malfunction.  
When you do not intend to use the player for a long time, remove the battery from the player.  
Do not use the player in a place subject to strong electromagnetic waves and X-rays (from  
magnetized objects such as magnets, speakers, televisions, etc.).  
Use only the supplied battery. When you want to replace the battery with a new one, consult  
your nearest Sony dealer or Sony Service Center.  
On heat build-up  
Heat may build up in the player if it is used for an extended period of time.  
continued  
ꢁꢄ  
ꢁꢅ  
 
Precautions (continued)  
On the supplied software  
On sample music and motion data  
Copyright laws prohibit reproducing the software or the manual accompanying it in whole or  
in part, or renting the software without the permission of the copyright holder.  
In no event will Sony be liable for any financial damage, or loss of profits, including claims  
made by third parties, arising out of the use of the software supplied with this player.  
In the event a problem occurs with this software as a result of defective manufacturing, Sony  
will replace it. However, Sony bears no other responsibility.  
The player is pre-installed with sample music and motion data so that you can try it out right  
away.  
To delete these music and motion data, delete them using Rolly Choreographer.  
Once you delete the music and motion data, you cannot restore them. The music and motion  
data will not be supplied again. You may import and store the sample music and motion data to  
your computer using Rolly Choreographer, before deleting them.  
The software provided with this player cannot be used with equipment other than that which is  
so designated.  
The recorded music is limited to private use only. Use of the music beyond this limit  
requires permission of the copyright holders.  
Sony is not responsible for incomplete recording/downloading or damaged data due to  
problems of the player or computer.  
Please note that, due to continued efforts to improve quality, the software specifications may be  
changed without notice.  
Operation of this player with software other than that provided is not covered by the warranty.  
The supplied software supports the OS languages of English and French. The ability to display  
the languages on the supplied software will depend on the installed OS on your PC. For better  
results, please ensure that the installed OS is compatible with the desired language you want to  
display.  
We do not guarantee all the languages will be able to be displayed properly on your language.  
User-created characters and some special characters may not be displayed.  
The explanations in this manual assume that you are familiar with the basic operations of  
Windows.  
On cleaning  
Clean the players case with a soft cloth, such as cleaning cloth for eyeglasses.  
If the player’s case becomes very dirty, clean it with a soft cloth slightly moistened with water or  
a mild detergent solution.  
Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzene, as  
it may mar the finish of the case.  
For details on the use of your computer and operating system, please refer to the respective  
manuals.  
Be careful not to let water get into the player from the opening near the connector.  
If you have any questions or problems concerning the player, please consult your nearest Sony  
dealer or Sony Service Center.  
ꢂ0  
ꢂ1  
 
 
Specifications  
Capacity (User available capacity)*  
2 GB (Approx. 1.88 GB = 2,028,175,360  
bytes)  
Audio compression technology  
MPEG-1 Audio Layer-3 (MP3)  
Advanced Audio Coding (AAC)*  
* AAC format audio files that are  
copyright-protected cannot be  
played.  
The player SEP-30BT  
Operating temperature  
5 °C to 35 °C (41 °F to 95 °F)  
Power source  
Bluetooth summery  
Communication system  
Bluetooth Standard version 2.0  
Output  
Bluetooth Standard Power Class 2  
Frequency band  
* Available storage capacity of the player  
may vary. A portion of the memory is  
used for data management functions.  
Rechargeable lithium-ion battery  
USB power (from a computer through  
the supplied USB cable)  
Maximum recordable number of tracks  
and playing time (Approx.)*  
Music data only  
Supported bit rates*  
2.4 GHz band (2.4000 GHz to  
2.4835 GHz)  
MP3: 32 to 320 kbps variable bit  
Battery life  
Speakers  
Approx. 20 mm (3/4 in) diameter  
Maximum output  
1.2 watts + 1.2 watts (with the fully  
charged battery)  
Interface  
USB jack: miniB  
Hi-speed USB (USB2.0 Compliant)  
Dimension  
rate-compliant  
AAC: 16 to 320 kbps variable bit  
rate-compliant  
Maximum communication distance  
Bit rate  
48 kbps  
64 kbps  
128 kbps  
256 kbps  
320 kbps  
Tracks  
1350  
1000  
515  
255  
205  
Time  
90 hr.  
66 hr. 40 min.  
34 hr. 20 min.  
17 hr.  
Approx. 10 m (30 feet)(1)  
Compatible Bluetooth profiles(2)  
A2DP (Advanced Audio Distribution  
Profile)  
* Nonstandard bit rates or non-  
guaranteed bit rates are included  
depending on the sampling  
frequency.  
AVRCP (Audio Video Remote Control  
Profile)  
13 hr. 40 min.  
Sampling frequency*  
MP3: 32, 44.1, 48 kHz  
AAC: 11.025, 12, 16, 22.05, 24, 32, 44.1,  
48 kHz  
* Sampling frequency may not  
correspond to all encoders.  
Music and motion data  
SPP (Serial Port Profile)  
Supported codecs(3)  
SBC (Sub Band Codec)  
MP3  
Bit rate  
48 kbps  
64 kbps  
128 kbps  
256 kbps  
320 kbps  
Tracks  
1050  
800  
450  
245  
Time  
70 hr.  
53 hr. 20 min.  
30 hr.  
16 hr. 20 min.  
13 hr. 20 min.  
Approx. 104 × 65 × 65 mm  
(Approx. 4 1/8 × 2 9/16 × 2 9/16 in)  
(w/h/d, projecting parts not included)  
(1) The actual range will vary depending on  
factors such as obstacles between devices,  
magnetic fields, static electricity, reception  
sensitivity, antenna (aerial) performance,  
operating system, software application, etc.  
(2) Bluetooth profiles are standardized according  
to the purpose of the Bluetooth device.  
(3) Codec indicates the audio signal compression  
and conversion format.  
Mass  
200  
Approx. 300 g (Approx. 10.6 oz) (the  
battery included)  
* The approximate tracks and times are based on  
a 4-minute MP3 format track and a 4-minute  
Sony standard motion (“self-motion”). They  
may be different with other audio file formats  
and the type of motion.  
continued  
ꢂꢆ  
ꢂꢇ  
 
 
Specifications (continued)  
Copyrights  
Rolly and  
are trademarks of Sony Corporation.  
Battery BT-SE10  
Microsoft, Windows, Windows NT and Windows Media are trademarks or registered  
trademarks of Microsoft Corporation in the United States and/or other countries.  
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such  
marks by Sony Corporation is under license. Other trademarks and trade names are those of  
their respective owners.  
MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and  
Thomson.  
Type  
Lithium ion rechargeable battery  
Maximum output voltage  
DC 4.2 V  
Output voltage  
DC 3.7 V  
Capacity  
IBM and PC/AT are registered trademarks of International Business Machines Corporation.  
Macintosh is a trademark of Apple Inc.  
1,560 mAh  
Operating temperature  
5 °C to 35 °C (41 °F to 95 °F)  
(charging temperature: 10 °C to 30 °C  
(50 °F to 86 °F))  
Pentium is a trademark or a registered trademark of Intel Corporation.  
All other trademarks and registered trademarks are trademarks or registered trademarks of  
their respective holders. In this manual, ™ and ® marks are not specified.  
This product is protected by certain intellectual property rights of Microsoft Corporation. Use  
or distribution of such technology outside of this product is prohibited without a license from  
Microsoft or an authorized Microsoft subsidiary.  
Dimension  
Approx. 22.2 × 26.8 × 44.7 mm  
(Approx. 7/8 × 1 1/16 × 1 3/4 in)(w/h/d)  
Program ©2008 Sony Corporation  
Documentation ©2008 Sony Corporation  
Design and specifications are subject to  
change without notice.  
Optional accessory  
Rolly Charging Cradle CDL-SE10  
ꢂꢀ  
ꢂꢁ  
 
 
Bluetooth Wireless Technology  
Around microwave ovens that are in use  
Locations where other electromagnetic waves occur  
Bluetooth wireless technology is a short-range wireless technology linking digital devices,  
such as personal computers and digital still cameras. Using the Bluetooth wireless  
technology, you can operate the units involved within a range of about 10 meters (30 feet).  
The Bluetooth wireless technology is commonly used between two devices, but a single  
device can be connected to multiple devices. You do not need wires to get connected as you  
do with a USB connection, and you do not need to place the devices face to face as you do  
with wireless infrared technology. You can use the technology with one Bluetooth device in  
your bag or pocket.  
Effects of other devices  
Bluetooth devices and wireless LAN (IEEE 802.11b/g) use the same frequency band (2.4 GHz).  
When using your Bluetooth device near a device with wireless LAN capability, electromagnetic  
interference may occur. This could result in lower data transfer rates, noise, or inability to  
connect. If this happens, try the following remedies:  
Try connecting this player and a Bluetooth device when you are at least 10 meters (30 feet) away  
from the wireless LAN equipment.  
Turn off the power to the wireless LAN equipment when using your Bluetooth device within 10  
meters (30 feet).  
Bluetooth wireless technology is a global standard supported by thousands of companies.  
These companies produce products that meet the global standard.  
Supported Bluetooth version and profiles  
Profile refers to a standard set of capabilities for various Bluetooth product capabilities. This  
system supports the following Bluetooth version and profiles.  
Supported Bluetooth version: Bluetooth Standard version 2.0  
Supported Bluetooth profiles:  
Effects on other devices  
The radio waves broadcast by this system may interfere with the operation of some medical  
devices. Since this interference may result in malfunction, always turn off the power on this  
player and a Bluetooth device in the following locations:  
A2DP (Advanced Audio Distribution Profile)  
AVRCP (Audio Video Remote Control Profile)  
SPP (Serial Port Profile)  
In hospitals, on trains, in airplanes, at gas stations, and any place where flammable gasses may  
be present  
Near automatic doors or fire alarms  
Effective communication range  
Notes  
Bluetooth devices should be used within approximately 10 meters (30 feet) (unobstructed  
distance) of each other.  
This player supports security functions that comply with the Bluetooth specification as a means  
of ensuring security during communication using Bluetooth technology. However, this security  
may be insufficient depending on the setting contents and other factors, so always be careful  
when performing communication using Bluetooth technology.  
Sony cannot be held liable in any way for damages or other loss resulting from information  
leaks during communication using Bluetooth technology.  
The effective communication range may become shorter under the following conditions.  
When a person, metal object, wall or other obstruction is between the devices with a Bluetooth  
connection  
Locations where a wireless LAN is installed  
continued  
ꢂꢂ  
ꢂꢃ  
 
   
Bluetooth Wireless Technology (continued)  
Index  
Bluetooth communication is not necessarily guaranteed with all Bluetooth devices that have the  
same profile as this player.  
Bluetooth devices connected with this player must comply with the Bluetooth specification  
prescribed by the Bluetooth SIG, Inc., and must be certified to comply. However, even when a  
device complies with the Bluetooth specification, there may be cases where the characteristics  
or specifications of the Bluetooth device make it impossible to connect, or may result in  
different control methods, display or operation.  
A
F
P
Adjusting the volume.........30  
Arm ..................................8, 11  
Firmware..............................48  
Format............................38, 39  
Pairing..................................42  
Play-button indicator  
............................... 9, 15, 34  
Playback  
B
I
Bluetooth communication  
......................................... 46  
Motion................................ 33  
Music .................................. 26  
Shuffle................................. 31  
Play button ............................8  
Power switch .......................10  
Battery..................................12  
Playback time .................... 16  
Remaining.......................... 15  
Bluetooth communication  
..........................................40  
Bluetooth connection.........44  
Bluetooth indicator ........9, 42  
Bluetooth wireless  
Initialize.........................38, 39  
Install....................................20  
Noise may occur or the audio may cut off depending on the Bluetooth device connected with  
this player, the communications environment, or surrounding conditions.  
M
Playable Bluetooth devices  
You can check the websites below for the Bluetooth compatible devices.  
For customers in the U.S.A.:  
<http://www.sony.com/rollysupport>  
For customers in Canada:  
English <http://www.sony.ca/ElectronicsSupport/>  
French <http://fr.sony.ca/ElectronicsSupport/>  
Motion playback.................33  
N
R
technology.......................66  
Normal playback ................31  
Reset button ..................10, 49  
Rolly Choreographer  
C
O
............................. 20, 23, 37  
Rolly Settings  
Changing a track.................28  
Charging the battery ..........12  
Operation  
in your hand....................... 27  
on a level surface............... 27  
Bluetooth Communication  
......................................... 37  
Operation Sound............... 37  
Volume Operation ............ 37  
Wake-up Timer ................. 38  
D
Deleting music....................24  
Device Information............38  
continued  
ꢂꢄ  
ꢂꢅ  
 
 
Index (continued)  
S
Sample music and motion  
data...................................61  
SCMS-T ...............................37  
Self-motion..........................33  
Shoulder.................................9  
Shuffle playback..................31  
Side lamp ...............................8  
Speaker...................................9  
Stopping playback ........26, 35  
Supplied accessories.............7  
System requirements..........21  
T
Transferring music .............23  
U
Uninstall ..............................22  
Updating the player............48  
USB jack.........................10, 13  
W
Wake-up Timer.............38, 39  
Wheel ...............................9, 11  
ꢃ0  
 

Sharp Stereo System XL E12H User Manual
Sony Camcorder XC ST30 User Manual
Sony Clock Radio 3 873 060 341 User Manual
Sony Network Router PCWA C100 User Manual
Sony Personal Computer PCV LX800 User Manual
Sony Portable CD Player Model D EJ715 User Manual
Sony Portable CD Player VGF AP1 User Manual
Speco Technologies DVR EZVR4 8 User Manual
StarTechcom Network Hardware NETRS2321POE User Manual
Tanaka Bicycle TPB 350GX User Manual