Sharp Computer Drive TM 20 User Manual

What Does PC Link Do?  
Before You Begin  
3. Connect the other end of the PC interface cable to the  
ConnectingYourTM-20 toYour PC  
Requirements  
-Backup Back up all TM-20 data to your PC  
PC interface connector of your TM-20.  
-Restore Restore backup file to your TM-20  
TM-20  
MENU  
-Address Utility  
Type new Address entries on your PC and then  
transfer them to your TM-20.  
Installing  
PREFERENCES  
(
)
!
@
#
$
%
&
^
1. Insert the PC Interface Software disk into your disk  
~
=
+
[
]
{
}
DEL  
ENTER  
drive.  
,
CAPS  
CUT  
COPY  
PASTE  
;
:
A
A
SMBL  
WORD  
?
-
MAIN  
DONE  
-
2. Click on the Windows [Start] button and then click [Run].  
System Requirements  
PC Interface Cable  
(supplied)  
3. Type a:\Setup.exe (using the drive letter of your disk  
TM-20  
Your PC  
drive) and click on the [OK] button.  
Windows 98, Windows 95, Windows NT4.0  
*
A series of screens will be presented.  
1. First turn off your PC and TM-20 before connecting or  
IBM-compatible 486 or Pentium processor (33MHz or greater  
*
4. Follow the on-screen instructions.  
disconnecting the PC interface cable.  
clock speed)  
TM-20  
MENU  
2. Connect the standard 9-pin connector of the PC  
8MB free hard disk space  
*
Note:  
interface cable to one of the COM Ports on your PC.  
16MB RAM available  
*
The Select Program Folder screen determines the folder  
that is selected when you access theTM-20 PC Interface  
program group by clicking [Programs] in the [Start] menu.  
By default, the folder is named "PC Interface Software for  
SharpTM-20". Changing the name is not recommended.  
PREFERENCES  
VGA monitor of better  
Note:  
*
®
You will need to purchase an adaptor if you wish to use a  
COM Port with a 25-pin connector.  
Microsoft Mouse or compatible Pointing Device  
*
(
)
!
@
#
$
%
&
^
[
]
{
}
3.5” disk drive  
~
=
+
*
DEL  
ENTER  
One available serial port with D-sub 9-pin connector  
,
CAPS  
CUT  
COPY  
PASTE  
;
:
*
A
A
SMBL  
WORD  
?
-
-
MAIN  
DONE  
TM-20  
MENU  
When installation is complete, a set of applications named PC  
Interface Software for Sharp TM-20 will have been created.  
You can access these applications using Windows [Start]-  
[Programs]-[PC Interface Software for Sharp TM-20].  
PREFERRENCES  
(
)
!
@
#
$
%
&
^
~
=
+
[
]
{
}
DEL  
ENTER  
,
CAPS  
CUT  
COPY  
PASTE  
;
:
98LT(TINSE1323PCZZ)  
OLY85EW000610  
A
A
SMBL  
WORD  
?
-
-
MAIN  
DONE  
3
85-EW00-061078  
PRINTED IN CHINA  
2
Getting Started  
Backup and Restore  
Placing theTM-20 in PC Link Mode  
Making a Backup  
Note:  
PC Interface Software Main Screen  
If you click [Cancel], the backup process will stop and  
return you to the Main Screen.  
When transferring data using the PC Interface Software, place the  
TM-20 in PC Link mode after first making sure that the TM-20 is  
properly connected to your PC.  
To access the PC Interface Software for Sharp TM-20 main  
screen, click the Windows [Start] button, select [Programs] and  
then click [PC Interface Software for Sharp TM-20].  
1. Connect your TM-20 to your PC and place the TM-20 in  
PC Link mode. Refer to “Placing the TM-20 in PC Link  
Mode” on this Guide.  
TM-20 procedure  
2. Click [Backup] on the Main Screen.  
Restoring a Backup  
1. Press POWER Key (  
) to turn on the power.  
Restoring data from the backup file on your PC will completely  
replace all the data in your TM-20 with the contents of the PC's  
backup file. Because the data in your TM-20 is completely deleted  
at the beginning of the restoration process, you cannot stop the  
process midway if you change your mind.  
MAIN  
2. Press  
in the lower left corner.  
3. Select PC Link (use  
right corner).  
ENTER  
,
,
and  
key in the lower  
4. Press  
.
When the following screen appears, the TM-20 is ready for PC  
Before restoring from a backup file it is a good idea to perform a  
secondary backup (in case your original backup is damaged).  
Link.  
1. Connect your TM-20 to your PC and place the TM-20 in  
PC Link mode.  
2. Click [Restore] on the Main Screen.  
3. Click [Browse] and select the ".sbk" file you want to  
All TM-20 PC Interface operations can be accessed from the Main  
Screen.  
restore.  
3. The TM-20's PC Interface Software will automatically fill  
in the Backup Filename field using today's date.  
You can retype the file name or select the file by clicking  
[Browse].  
Setting COM Port Options  
4. Click [NEXT].  
5. A confirmation screen will appear. If you are sure you  
want to restore, click [NEXT]. Restoration will start and  
end automatically.  
After placing the TM-20 in PC Link mode, click [Option] on the  
Main Screen to open the Communication Port (COM Port) options  
window. When you click [Auto Detect], an appropriate COM Port  
will automatically be selected. When the appropriate port is  
selected, click [OK].  
4. Click [NEXT].  
5. A confirmation screen will appear. Click [Next] to start  
the backup process.  
 

Sennheiser Microphone E 609 User Manual
Snapper Snow Blower SS50220E 7800080 ES50220E 7800083 User Manual
Sony Battery Charger VGPBPSC27 User Manual
Sony Network Card PCLK MN10A User Manual
Sony Webcam VPCM1 User Manual
SpeakerCraft Speaker AIM7 FIVE User Manual
Superior Indoor Fireplace SLDVT 30NE User Manual
SVAT Electronics Digital Camera GX5204 User Manual
Sylvania Flat Panel Television LC320SS9 User Manual
Tannoy Portable Speaker CMS801 DC User Manual