SIIG Film Camera 04 0414D User Manual

CyberSerial Dual  
ExpressCard  
QuickInstallationGuide  
Introducing the CyberSerial ExpressCard  
The CyberSerial Dual ExpressCard adds two high-speed  
serial ports to an ExpressCard equipped computer.  
FeaturesandBenefits  
Compatible with hi-speed modems, monitoring  
equipment, serial networking and other serial  
devices  
Two DB9 RS232 ports with 16550 UART  
Supports data rate of up to 115 Kbps  
Built-in 16-byte FIFO buffers dramatically increase  
data transmit/receive speed, especially under  
Windows multitasking environment  
SystemRequirements  
Notebook or desktop computer with an available  
ExpressCard slot  
Windows® 2000/XP (32-/64-bit)/Server 2003  
(32-/64-bit)/Vista (32-bit)  
PackageContents  
CyberSerialDualExpressCard  
2-Port DB9 Fan-out Cable  
Driver CD  
Quick Installation Guide  
04-0414D  
 
1
Hardware Installation  
General instructions for installing the ExpressCard are  
providedbelow. Sincethedesignofnotebookcomputers  
vary, refer to your systems reference manual for further  
information, if needed.  
1.  
Insert the CyberSerial Dual ExpressCard into the  
ExpressCard slot of the computer with it's Express  
Card Connector facing the slot. Push the card into  
the slot gently, yet firmly for a solid connection.  
Note: Some ExpressCard slots will click when the  
ExpressCard is fully inserted into the slot.  
2. Connect 2S of the fan-out cable to the Fan-out Cable  
Connector of the CyberSerial Dual ExpressCard. See  
Figure 1 and 2 on page 2 for more information.  
Note: MakesurethattheCyberSerialDualExpressCard  
does not move from side to side when connecting  
the fan-out cable, otherwise, the ExpressCard may  
eject from the slot.  
3.  
If your system was powered off when you plugged  
intheCyberSerialDualExpressCard, turnitonandgo  
to Driver Installation. Otherwise, go directly to  
DriverInstallation.  
Driver Installation  
This section provides information on how to install the  
CyberSerial Dual ExpressCard drivers.  
Windows2000  
1. At the Found New Hardware Wizard, click Next.  
2. Select Search for a suitable driver for my device  
(recommended), and click Next.  
3
 
3. Check Specify a location, uncheck the other boxes,  
then click Next.  
4. InsertthedriverCD,typeinD:\2000,thenclickOK.  
(Change D: to match your CD-ROM drive letter)  
5. Click Next and Finish.  
6. Repeat steps 1-5 to complete the driver installation.  
WindowsXP  
1. At the Found New Hardware Wizard, select No,  
not this time, then click Next.  
2. Select Install from a list or specific location  
(Advanced), then click Next.  
3. Insert the driver CD, check Include this location in  
the search, uncheck the other box.  
For32-bit:TypeinD:\XP,thenclickNext. (Change  
D: to match your CD-ROM drive letter)  
For 64-bit: Type in D:\64bit, then click Next.  
(Change D: to match your CD-ROM drive letter)  
4. IftheHardwareInstallationwindowpopsup,click  
Continue Anyway, then Finish. Our driver has been  
thoroughlytestedforstabilityandcompatibility.  
5. Repeat steps 1-4 two times to complete the  
installation.  
WindowsServer2003  
1. At the Found New Hardware Wizard, select No,  
not this time, then click Next.  
2. Select Install from a list or specific location  
(Advanced), then click Next.  
4
 
3. Insert the driver CD, check Include this location in  
the search, uncheck the other box.  
For32-bit:TypeinD:\2003,thenclickNext. (Change  
D: to match your CD-ROM drive letter)  
For 64-bit: Type in D:\64bit, then click Next.  
(Change D: to match your CD-ROM drive letter)  
4. IftheHardwareInstallationwindowpopsup,click  
Continue Anyway, then Finish. Our driver has been  
thoroughlytestedforstabilityandcompatibility.  
5. Repeat steps 1-4 two times to complete the  
installation.  
WindowsVista™  
1. Click Locate and install driver software  
(recommended), then click Continue. Click Don't  
search online.  
2. Insert driver CD. Click Browse my computer for  
driver software (advanced), type in D:\Vista, then  
click Next. (Change D: to match your CD-ROM  
drive letter)  
3. If the Windows Security windows pops up, click  
Installthedriversoftwareanyway,thenclickClose.  
4. Click Don't search online, click Next. If the  
Windows Security window pops up, click Install  
the driver software anyway.  
5. Click Close to complete the installation.  
ToVerifyWindowsInstallation  
1. Check Device Manager to verify successful driver  
installation.  
Windows 2000/XP/Server 2003: Right click My  
Computer, click Manage, click Device Manager.  
5
 
WindowsVista:RightclickComputer,clickManage,  
click Continue, then click Device Manager.  
2. Click on the + (plus sign) in front of Ports (COM &  
LPT),twoUSB-to-SerialPort...shouldbedisplayed.  
Changing COM Port Number  
Some serial devices need a specific COM port in order to  
work. If your serial device works properly, do not  
change this setting.  
1. From the Device Manager window double click  
Ports (COM & LPT), then double click the serial  
port you want to change.  
2. Click Features tab.  
3. Click the down arrow that is next to the COM Port  
Number box, select a COM port that is not in use,  
then click OK.  
4. Close Device Manager to save the changes.  
Removing the ExpressCard  
Before ejecting the CyberSerial Dual ExpressCard from the  
computer, first use the Safely Remove Hardware utility  
to stop it. Not following the steps below could lead to  
system crashes, data corruption or data loss.  
1. Click the Unplug or Eject Hardware or Safely  
Remove Hardware icon located in the taskbar by  
the system clock.  
2. ClickStopUSBCompoundDeviceorSafelyremove  
USB Compound Device.  
3. AttheSafeToRemoveHardwarebox,theCyberSerial  
Dual ExpressCard can be ejected from the computer.  
6
 
Technical Support and Warranty  
QUESTIONS? SIIGsOnlineSupporthasanswers! Simplyvisitour  
web site at www.siig.com and click Support. Our online support  
database is updated daily with new drivers and solutions. Answers  
toyourquestionscouldbejustafewclicksaway. Youcanalsosubmit  
questions online and a technical support analysts will promptly  
respond.  
SIIGoffersalifetimemanufacturerwarrantywiththisproduct. Please  
see our web site for more warranty details. If you encounter any  
problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the  
product to the store where you purchased from.  
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please  
follow these steps to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit a  
request to SIIG RMA. If the product is determined to be  
defective,anRMAnumberwillbeissued. SIIGRMAdepartment  
can also be reached at (510) 413-5333.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All software, cable(s)  
and any other accessories that came with the original package  
must be included.  
Clearly write your RMA number on the top of the returned  
package. SIIG will refuse to accept any shipping package, and  
will not be responsible for a product returned without an  
RMA number posted on the outside of the shipping carton.  
You are responsible for the cost of shipping. Ship the product  
to the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA#:  
SIIG will ship the repaired or replaced product via Ground  
in the U.S. and International Economy outside of the U.S. at  
no cost to the customer.  
7
 
About SIIG, Inc.  
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer  
ofI/Oconnectivityproducts,includingPCI&ISAserialandparallel  
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),  
networking, sound cards, and other accessories. SIIG is the premier  
one-stop source of upgrades.  
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly  
features, and are backed by an extensive manufacturer warranty.  
High-quality control standards are evident by the overall ease of  
installation and compatibility of our products, as well as one of the  
lowest defective return rates in the industry. SIIG products can be  
found in computer retail stores, mail order catalogs, through major  
distributors, system integrators, and VARs in the Americas and the  
UK,andthroughe-commercesites.  
PRODUCT NAME  
CyberSerial Dual ExpressCard  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS  
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
CyberSerial Dual ExpressCard is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered  
trademarksofSIIG,Inc. Microsoft,WindowsandWindowsVistaareeitherregisteredtrademarksor  
trademarksofMicrosoftCorporationintheUnitedStatesand/orothercountries. Othernamesusedin  
thispublicationareforidentificationonlyandmaybetrademarksoftheirrespectivecompanies.  
January, 2008  
Copyright © 2008 by SIIG, Inc. All rights reserved.  
 

Sharp Flat Panel Television PN 455RU User Manual
Sharp Toaster KZ P2DW User Manual
Sony Laptop VPCW121AXP User Manual
Sony MiniDisc Player MDS B1 User Manual
Sony Portable CD Player D EJ365 User Manual
Sony Video Game Console SCPH 75007 User Manual
Southbend Electric Steamer Counter Steamer User Manual
SOYO Computer Hardware SY 6VBA 133 User Manual
Specialized Bicycle Accessories Stumpjumper Adjustable Dropout User Manual
Spectra Laser Level GL612 User Manual